 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| GS1582 Multi-Rate Serializer with Cable Driver, Audio Multiplexer and ClockCleanerTM GS1582 Data Sheet Key Features * * * * HD-SDI, SD-SDI, DVB-ASI transmitter with audio embedding Integrated SMPTE 292M and 259M-C compliant cable driver Integrated ClockCleanerTM User selectable video processing features, including: * * * * * * * * * * Generic ancillary data insertion Support for HVF or EIA/CEA-861 timing input Automatic standard detection and indication Enhanced SMPTE 352M payload identifier generation and insertion TRS, CRC, ANC data checksum, and line number calculation and insertion EDH packet generation and insertion Illegal code remapping SMPTE 292M and SMPTE 259M-C compliant scrambling and NRZ NRZI encoding Blanking of input HANC and VANC space Description The GS1582 is the next generation multi-standard serializer with an integrated cable driver. The device provides robust parallel to serial conversion, generating a SMPTE 292M/259M-C compliant serial digital output signal. The integrated cable driver features an output disable (high impedance) mode and an adjustable signal swing. Data input is accepted in 20-bit parallel format or 10-bit parallel format. An associated parallel clock input must be provided at the appropriate operating frequency; 74.25/74.1758/13.5MHz (20-bit mode) or 148.5/148.352/27MHz (10-bit mode). The GS1582 features an internal PLL which, if desired, can be configured for a loop bandwidth below 100kHz. When used in conjunction with the GO1555 Voltage Controlled Oscillator, the GS1582 can tolerate well in excess of 300ps jitter on the input PCLK and still provide output jitter within SMPTE specifications. In addition to serializing the input, the GS1582 performs NRZ-to-NRZI encoding and scrambling as per SMPTE 292M/259M-C when operating in SMPTE mode. When operating in DVB-ASI mode, the device will insert K28.5 sync characters and 8b/10b encode the data prior to serialization. The device also provides a range of other data processing functions. All processing features are optional and may be enabled/disabled via external control pin(s) and/or host interface programming. The GS1582 can embed up to 8 channels of audio into the video data stream in accordance with SMPTE 299M and SMPTE 272M. The audio input signal formats supported by the device include AES/EBU and I2S serial digital formats with a 16, 20 or 24 bit sample size and a 48 kHz sample rate. Additional audio processing features include individual channel enable, channel swap, group swap, ECC generation and audio channel status insertion. Typical power consumption, including the GO1555 VCO, is 500mW. The standby feature allows the power to be reduced to 125mW. Power may be reduced to less than 10mW by also removing the power to the cable driver and eliminating transitions at the parallel data and clock inputs. The GS1582 is Pb-free and RoHS compliant. User selectable audio processing features, including: * * * SMPTE 299M and SMPTE 272M-A/C compliant audio embedding Support for up to 8 channels Support for audio group replacement * * * * * * JTAG test interface 1.8V core and 3.3V charge pump power supply 1.8V and 3.3V digital I/O support Low power standby mode Operating temperature range: -20oC to +85oC Pb-free, RoHS compliant, 11mm x 11mm 100-ball BGA package Applications * * SMPTE 292M and SMPTE 259M-C Serial Digital Interfaces DVB-ASI Serial Digital Interfaces 40117 - 1 November 2007 1 of 114 www.gennum.com GS1582 Data Sheet Functional Block Diagram SDOUT_TDO SDIN_TDI SCLK_TCLK CS_TMS DVB_ASI Host Interface AUDIO_INT GRP1_EN/DIS GRP2_EN/DIS Ain_1/2 Ain_3/4 Ain_5/6 Ain_7/8 ACLK1 ACLK2 WCLK1 WCLK2 F/DE V/VSYNC H/HSYNC TIM_861 DIN[19:0] PCLK GSPI SD/HD Audio Embedding Input Mux/ Demux HANC/ VANC Blanking RSET SMPTE 352M Generation and Insertion ANC Data Insertion TRS, Line Number and CRC Insertion EDH Packet Insertion NRZ/NRZI SMPTE SCRAMBLER Mux Parallel to Serial Converter SMPTE Cable Driver SDO SDO SDO_EN/DIS DVB ASI ENDEC PhaseDetector/ Chargepump 2.5V Regulator LOCKED ClockCleanerTM VCO_GND VCO_VCC VCO LF CP_RES GS1582 Functional Block Diagram 40117 - 1 November 2007 2 of 114 GS1582 Data Sheet Contents Key Features .................................................................................................................1 Applications...................................................................................................................1 Description ....................................................................................................................1 Functional Block Diagram .............................................................................................2 1. Pin Out ......................................................................................................................7 1.1 Pin Assignment ...............................................................................................7 1.2 Pin Descriptions ..............................................................................................8 2. Electrical Characteristics .........................................................................................17 2.1 Absolute Maximum Ratings ..........................................................................17 2.2 Recommended Operating Conditions ...........................................................17 2.3 DC Electrical Characteristics ........................................................................18 2.4 AC Electrical Characteristics .........................................................................19 2.5 Solder Reflow Profiles ...................................................................................21 3. Input/Output Circuits ...............................................................................................22 4. Detailed Description ................................................................................................25 4.1 Functional Overview .....................................................................................25 4.2 Parallel Data Inputs .......................................................................................26 4.2.1 Parallel Input in SMPTE Mode.............................................................26 4.2.2 Parallel Input in DVB-ASI Mode...........................................................26 4.2.3 Parallel Input in Data-Through Mode...................................................27 4.2.4 Parallel Input Clock (PCLK) .................................................................27 4.3 SMPTE Mode ................................................................................................28 4.3.1 HVF Timing..........................................................................................28 4.3.2 CEA 861 Timing...................................................................................29 4.4 DVB-ASI mode ..............................................................................................34 4.4.1 Control Signal Inputs ...........................................................................34 4.5 Data-Through Mode ......................................................................................35 4.6 Standby Mode ...............................................................................................35 4.7 Audio Multiplexer ..........................................................................................36 4.7.1 Audio Core Configurations...................................................................36 4.7.2 Audio Detection ...................................................................................37 4.7.3 Audio Modes of Operation ...................................................................38 4.7.4 Audio Packet Delete ............................................................................39 4.7.5 Arbitrary, SMPTE 352M & EDH Packet Detect ...................................40 4.7.6 Audio Packet Multiplexing....................................................................41 4.7.7 Audio Insertion After Video Switching Point ........................................41 4.7.8 Audio Data Packets .............................................................................42 4.7.9 Audio Control Packets .........................................................................45 4.7.10 Setting Packet DID ............................................................................47 4.7.11 Audio Group Replacement ................................................................48 40117 - 1 November 2007 3 of 114 GS1582 Data Sheet 4.7.12 Channel and Group Activation...........................................................50 4.7.13 ECC Error Detection & Correction (HD Mode Only) ..........................50 4.7.14 Interrupt Control.................................................................................50 4.7.15 Audio Clocks ......................................................................................50 4.7.16 5-frame Sequence Detection .............................................................51 4.7.17 Audio Input Format ............................................................................52 4.7.18 Audio Channel Status Input ...............................................................55 4.7.19 Audio Crosspoint ...............................................................................56 4.7.20 Audio Word Clock ..............................................................................57 4.7.21 GS1582 SD Audio FIFO Block ..........................................................58 4.7.22 Audio Sample Distributions................................................................59 4.7.23 Audio Mute.........................................................................................62 4.8 Ancillary Data Insertion .................................................................................62 4.8.1 Ancillary Data Insertion Operating Mode .............................................63 4.8.2 HANC Insertion....................................................................................64 4.8.3 VANC Insertion ....................................................................................65 4.9 Additional Processing Functions ...................................................................65 4.9.1 ANC Data Blanking..............................................................................65 4.9.2 Automatic Video Standard Detection...................................................65 4.9.3 Video Standard Indication....................................................................66 4.9.4 Packet Generation and Insertion .........................................................68 4.10 Parallel to Serial Conversion .......................................................................73 4.11 Internal ClockCleanerTM PLL ......................................................................74 4.11.1 External VCO .....................................................................................74 4.11.2 Loop Filter..........................................................................................74 4.11.3 Lock Detect Output ............................................................................75 4.12 Serial Digital Output ....................................................................................76 4.12.1 Output Swing .....................................................................................76 4.13 GSPI Host Interface ....................................................................................76 4.13.1 Command Word Description..............................................................78 4.13.2 Data Read and Write Timing .............................................................78 4.13.3 Configuration and Status Registers ...................................................80 4.14 JTAG Test Operation ................................................................................105 4.15 Device Reset .............................................................................................107 5. Application Reference Design ...............................................................................108 5.1 Typical Application Circuit (Part A) .............................................................108 5.2 Typical Application Circuit (Part B) .............................................................109 6. References & Relevant Standards ........................................................................110 7. Package & Ordering Information ...........................................................................111 7.1 Package Dimensions ..................................................................................111 7.2 Marking Diagram .........................................................................................112 7.3 Packaging Data ...........................................................................................112 7.4 Ordering Information ...................................................................................112 8. Revision History ....................................................................................................113 40117 - 1 November 2007 4 of 114 GS1582 Data Sheet List of Figures Figure 2-1: Maximum Pb-free Solder Reflow Profile ..................................................21 Figure 3-1: Differential Output Stage (SDO/SDO) .....................................................22 Figure 3-2: Charge Pump Current Setting Resistor (CP_RES) ..................................22 Figure 3-3: PLL Loop Filter ........................................................................................23 Figure 3-4: VCO Input ................................................................................................23 Figure 3-5: Digital Input Pin with Weak Pull Up(>33kW) (ACLK[2:1], WCLK[2:1], AIN[4:1], PCLK, DIN[19:0]) .................................................24 Figure 3-6: 5V Tolerant Input Pin (All Other Input Pins) .............................................24 Figure 3-7: Digital Output Pin with High Impedance Mode (LOCKED, AUDIO_INT, SDOUT_TDO) .....................................................................24 Figure 4-1: PCLK to Data Timing ...............................................................................26 Figure 4-2: H_Blanking, V_Blanking, F_Digital Timing ..............................................29 Figure 4-3: HSYNC:VSYNC:DE Input Timing 1280 x 720p @ 59.94/60 ....................31 Figure 4-4: HSYNC:VSYNC:DE Input Timing 1920 x 1080i @ 59.94/60 ...................31 Figure 4-5: HSYNC:VSYNC:DE Input Timing 720 (1440) x 480i @ 59.94/60 ...........32 Figure 4-6: HSYNC:VSYNC:DE Input Timing 1280 x 720p @ 50 ..............................33 Figure 4-7: HSYNC:VSYNC:DE Input Timing 1920 x 1080i @ 50 .............................33 Figure 4-8: HSYNC:VSYNC:DE Input Timing 720 (1440) x 576 @ 50 ......................34 Figure 4-9: DVB-ASI FIFO Implementation using the GS1582 ..................................35 Figure 4-10: Audio Multiplexer Top Level ..................................................................37 Figure 4-11: Ancillary Data Packet Placement Example ............................................39 Figure 4-12: SD Audio Data Packet Structure ...........................................................42 Figure 4-13: SD Extended Audio Data Packet Structure ...........................................43 Figure 4-14: HD Audio Data Packet Structure ...........................................................43 Figure 4-15: SD Audio Control Packet Structure .......................................................45 Figure 4-16: HD Audio Control Packet Structure .......................................................46 Figure 4-17: Audio Group Replacement Example (HD Formats) ...............................49 Figure 4-18: ACLK to Data & Control Signal Input Timing .........................................51 Figure 4-19: AES/EBU Sub-frame Formatting ...........................................................54 Figure 4-20: AES/EBU Audio Input Format ................................................................54 Figure 4-21: Serial Audio Input: Left Justified; MSB First ..........................................54 Figure 4-22: Serial Audio Input: Left Justified; LSB First ...........................................55 Figure 4-23: Serial Audio Input: Right Justified; MSB First ........................................55 Figure 4-24: Serial Audio Input: Right Justified; LSB First .........................................55 Figure 4-25: I2S Audio Input .......................................................................................55 Figure 4-26: Gennum Serial Peripheral Interface (GSPI) ..........................................77 Figure 4-27: Command Word .....................................................................................78 Figure 4-28: Data Word ..............................................................................................78 Figure 4-29: GSPI Read Mode Timing .......................................................................79 Figure 4-30: GSPI Write Mode Timing .......................................................................79 Figure 4-31: In-Circuit JTAG ....................................................................................106 Figure 4-32: System JTAG .......................................................................................106 Figure 4-33: Reset Pulse .........................................................................................107 40117 - 1 November 2007 5 of 114 GS1582 Data Sheet List of Tables Table 1-1: Pin Descriptions .......................................................................................... 8 Table 2-1: Recommended Operating Conditions ....................................................... 17 Table 2-2: DC Electrical Characteristics .................................................................... 18 Table 2-3: AC Electrical Characteristics..................................................................... 19 Table 4-1: Parallel Data Input Format ........................................................................ 27 Table 4-2: Standby Power Consumption ................................................................... 36 Table 4-3: Audio Multiplexer Modes of Operation ...................................................... 39 Table 4-4: Non-audio Ancillary Data Packet DIDs ..................................................... 40 Table 4-5: Audio Data Packet Word Descriptions ...................................................... 42 Table 4-6: Extended Audio Data Packet Word Descriptions...................................... 43 Table 4-7: Audio Data Packet Word Descriptions ...................................................... 44 Table 4-8: Audio Control Packet Word Descriptions .................................................. 45 Table 4-9: Audio Control Packet Word Descriptions .................................................. 46 Table 4-10: Audio Group DID Host Interface Settings ............................................... 48 Table 4-11: Audio Data and Control Packet DID Setting Register ............................. 48 Table 4-12: GS1582 Serial Audio Data Inputs ........................................................... 51 Table 4-13: Frame Rates with AFN = 0...................................................................... 52 Table 4-14: Frame Rates with varying samples per frame ........................................ 52 Table 4-15: Audio Input Formats................................................................................ 53 Table 4-16: Audio Channel Status Block Default Settings ......................................... 56 Table 4-17: Audio Channel Status Information Register Settings .............................. 56 Table 4-18: Audio Channel Mapping Codes .............................................................. 57 Table 4-19: Source Input Address Registers ............................................................. 57 Table 4-20: Audio Clock Selection Host Interface Settings........................................ 58 Table 4-21: Audio Buffer Pointer Offset Settings ....................................................... 59 Table 4-22: 5-frame Sequence Sample Distribution .................................................. 59 Table 4-23: Group 1 Audio Sample Distribution......................................................... 60 Table 4-24: Group 2 Audio Sample Distribution......................................................... 60 Table 4-25: Group 3 Audio Sample Distribution......................................................... 60 Table 4-26: Group 4 Audio Sample Distribution......................................................... 60 Table 4-27: Group 1 Audio Sample Distribution......................................................... 61 Table 4-28: Group 2 Audio Sample Distribution......................................................... 61 Table 4-29: Group 3 Audio Sample Distribution......................................................... 61 Table 4-30: Group 4 Audio Sample Distribution......................................................... 61 Table 4-31: Synchronous Audio Sample Distributions ............................................... 62 Table 4-32: Host Interface Description for Video Standard Register ......................... 66 Table 4-33: Host Interface Description for Raster Structure Registers ..................... 66 Table 4-34: Supported Video Standards.................................................................... 67 Table 4-35: Host Interface Description for Internal Processing Disable Register ...... 69 Table 4-36: Host Interface Description for SMPTE 352M Packet Line Number Insertion Registers ..................................................................................................... 70 Table 4-37: Host Interface Description for SMPTE 352M Payload Identifier Registers .................................................................................................................... 70 Table 4-38: Host Interface Description for EDH Flag Register (SD Mode Only)........ 72 Table 4-39: Serial Digital Output Rates...................................................................... 74 Table 4-40: Loop Filter Component Values ............................................................... 75 Table 4-41: GSPI Timing Parameters ........................................................................ 79 Table 4-42: GS1582 Internal Registers...................................................................... 80 Table 4-43: Video Configuration and Status Registers .............................................. 81 Table 4-44: SD Audio Configuration and Status Registers ........................................ 88 Table 4-45: HD Audio Configuration and Status Registers ........................................ 98 40117 - 1 November 2007 6 of 114 GS1582 Data Sheet 1. Pin Out 1.1 Pin Assignment 1 A B C D E F G H J K DIN17 2 DIN18 3 F/DE 4 H/HSYNC 5 CORE _VDD 6 PD_VDD 7 LF 8 VCO_ VCC 9 VCO 10 CP_VDD DIN15 DIN16 DIN19 PCLK CORE _GND PD_VDD CP_RES VCO_ GND VCO_ GND CP_GND DIN13 DIN14 DIN12 V/VSYNC CORE _GND PD_GND PD_GND PD_GND CD_GND SDO DIN11 DIN10 STANDBY SDO_EN/ DIS CORE _GND NC NC NC CD_GND SDO CORE _VDD CORE _GND SD/HD NC CORE _GND CORE _GND CORE _GND NC CD_GND CD_VDD DIN9 DIN8 DETECT _TRS RSV CORE _GND CORE _GND CORE _GND NC CD_GND RSET IO_VDD IO_GND TIM 861 20bit/ 10bit DVB_ASI SMPTE_ IOPROC BYPASS _EN/DIS GRP2_ EN/DIS GRP1_ EN/DIS AUDIO _INT RESET CORE _GND CORE _VDD DIN7 DIN6 ANC_ BLANK LOCKED JTAG/ HOST CORE _GND IO_GND IO_VDD DIN5 DIN4 DIN1 Ain_5/6 WCLK_2 Ain_1/2 WCLK_1 SDOUT _TDO SCLK _TCLK SDIN _TDI DIN3 DIN2 DIN0 Ain_7/8 ACLK_2 Ain_3/4 ACLK_1 CORE _VDD CS_ TMS 40117 - 1 November 2007 7 of 114 GS1582 Data Sheet 1.2 Pin Descriptions Table 1-1: Pin Descriptions Pin Number A1, A2, B1, B2, B3, C1, C2, C3, D1, D2 Name DIN[19:10] Timing Synchronous with PCLK Type Input Description PARALLEL DATA BUS Signal levels are LVCMOS/LVTTL compatible. DIN19 is the MSB and DIN10 is the LSB. HD 20-bit mode SD/HD = LOW 20bit/10bit = HIGH Luma data input in SMPTE mode SMPTE_BYPASS = HIGH DVB_ASI = LOW Data input in Data-Through mode SMPTE_BYPASS = LOW DVB_ASI = LOW HD 10-bit mode SD/HD = LOW 20bit/10bit = LOW Multiplexed Luma and Chroma data input in SMPTE mode SMPTE_BYPASS = HIGH DVB_ASI = LOW Data input in Data-Through mode SMPTE_BYPASS = LOW DVB_ASI = LOW SD 20-bit mode SD/HD = HIGH 20bit/10bit = HIGH Luma data input in SMPTE mode SMPTE_BYPASS = HIGH DVB_ASI = LOW Data input in Data-Through mode SMPTE_BYPASS = LOW DVB_ASI = LOW DVB-ASI data input in DVB-ASI mode SMPTE_BYPASS = LOW DVB_ASI = HIGH SD 10-bit mode SD/HD = HIGH 20bit/10bit = LOW Multiplexed Luma and Chroma data input in SMPTE mode SMPTE_BYPASS = HIGH DVB_ASI = LOW Data input in data through mode SMPTE_BYPASS = LOW DVB_ASI = LOW DVB-ASI data input in DVB-ASI mode SMPTE_BYPASS = LOW DVB_ASI = HIGH 40117 - 1 November 2007 8 of 114 GS1582 Data Sheet Table 1-1: Pin Descriptions (Continued) Pin Number A3 Name F/DE Timing Synchronous with PCLK Type Input Description PARALLEL DATA TIMING Signal levels are LVCMOS/LVTTL compatible. TIM_861 = LOW: Used to indicate the ODD / EVEN field of the video signal when DETECT_TRS is set LOW. The device will set the F bit in all outgoing TRS signals for the entire period that the F input signal is HIGH (IOPROC_EN/DIS must also be HIGH). The F signal should be set HIGH for the entire period of field 2 and should be set LOW for all lines in field 1 and for all lines in progressive scan systems. The F signal is ignored when DETECT_TRS = HIGH. TIM_861 = HIGH: The DE signal is used to indicate the active video period. DE is HIGH for active data and LOW for blanking. See Section 4.3.1 and Section 4.3.2 for timing details. The DE signal is ignored when DETECT_TRS = HIGH. A4 H/HSYNC Synchronous with PCLK Input PARALLEL DATA TIMING Signal levels are LVCMOS/LVTTL compatible. TIM_861 = LOW: The H signal is used to indicate the portion of the video line containing active video data, when DETECT_TRS is set low. Active Line Blanking The H signal should be set HIGH for the entire horizontal blanking period, including the EAV and SAV TRS words, and LOW otherwise. This is the default setting. TRS Based Blanking (H_CONFIG = 1h) The H signal should be set HIGH for the entire horizontal blanking period as indicated by the H bit in the received TRS ID words, and LOW otherwise. The H signal is ignored when DETECT_TRS = HIGH. TIM_861 = HIGH: The HSYNC signal indicates horizontal timing. See Section 4.3.1 for timing details. The HSYNC signal is ignored when DETECT_TRS = HIGH. A5, E1, G10, K8 A6, B6 A7 A8 A9 A10 CORE_VDD PD_VDD LF VCO_VCC VCO CP_VDD Non Synchronous Analog Analog Analog Analog Analog Input Power Input Power Input Output Power Input Input Power Power supply connection for the digital core logic. Connect to +1.8V DC digital. Power supply connection for the phase detector. Connect to +1.8V DC analog. PLL loop filter connection. Power supply for the external voltage controlled oscillator. 2.5V DC supplied by the device to the external VCO. Input from external VCO. Power supply connection for the charge pump and on chip VCO regulator. Connect to +3.3V DC analog. 40117 - 1 November 2007 9 of 114 GS1582 Data Sheet Table 1-1: Pin Descriptions (Continued) Pin Number B4 Name PCLK Timing - Type Input Description PARALLEL DATA BUS CLOCK Signal levels are LVCMOS/LVTTL compatible. HD 20-bit mode HD 10-bit mode SD 20-bit mode SD 10-bit mode PCLK = 74.25MHz or 74.25/1.001MHz PCLK = 148.5MHz or 148.5/1.001MHz PCLK = 13.5MHz PCLK = 27MHz B5, C5, D5, E2, E5, E6, E7, F5, F6, F7, G9, J8 C6, C7, C8 B7 B8, B9 B10 C4 CORE_GND Non Synchronous Input Power Ground connection for the digital core logic. Connect to digital GND. PD_GND CP_RES VCO_GND CP_GND V/VSYNC Analog - Analog Analog Synchronous with PCLK Input Power Input Output Power Input Power Input Ground connection for the phase detector. Connect to analog GND. Charge pump current setting resistor. Ground pins for the VCO. Ground pin for the charge pump and PLL. PARALLEL DATA TIMING Signal levels are LVCMOS/LVTTL compatible. TIM_861 = LOW: The V signal is used to indicate the portion of the video field/frame that is used for vertical blanking, when DETECT_TRS is set LOW. The V signal should be set HIGH for the entire vertical blanking period and should be set LOW for all lines outside of the vertical blanking interval. The V signal is ignored when DETECT_TRS = HIGH. TIM_861 = HIGH: The VSYNC signal indicates vertical timing. See Section 4.3.1 for timing details. The VSYNC signal is ignored when DETECT_TRS = HIGH. C9, D9, E9, F9 C10, D10 CD_GND SDO, SDO Analog Analog Input Power Output Ground connection for the serial digital cable driver. Connect to analog GND. Serial digital output signal operating at 1.485Gb/s, 1.485/1.001Gb/s, or 270Mb/s. The slew rate of these outputs is automatically controlled to meet SMPTE 292M and 259M requirements according to the setting of the SD/HD pin. Serial digital output signal from the internal cable driver. NOTE: The SDO/SDO output signals will be set to high impedance when RESET = LOW. 40117 - 1 November 2007 10 of 114 GS1582 Data Sheet Table 1-1: Pin Descriptions (Continued) Pin Number D3 Name STANDBY Timing Non Synchronous Type Input Description CONTROL SIGNAL INPUT Signal levels are LVCMOS/LVTTL compatible. Power down input. When set HIGH, the device will be in standby mode. D4 SDO_EN/DIS Non Synchronous Input CONTROL SIGNAL INPUT Signal levels are LVCMOS/LVTTL compatible. Used to enable or disable the serial digital output stage. When set LOW, the serial digital output signals SDO and SDO are disabled and become high impedance. When set HIGH, the serial digital output signals SDO and SDO are enabled. The SDO and SDO outputs will also be high impedance when the RESET pin is LOW. D6, D7, D8, E4, E8, F8 E3 NC SD/HD - Non Synchronous - Input No connect. Not connected internally. CONTROL SIGNAL INPUT Signal levels are LVCMOS/LVTTL compatible. When set LOW, the device will be configured to transmit signals of 1.485Gb/s - 1.485/1.001Gb/s rates only. When set HIGH, the device will be configured to transmit signals of a 270Mb/s rate only. E10 F1, F2, H1, H2, J1, J2, J3, K1, K2, K3 CD_VDD DIN[9:0] Analog Synchronous with PCLK Input Power Input Power supply connection for the serial digital cable driver. Connect to +3.3V DC analog. PARALLEL DATA BUS Signal levels are LVCMOS/LVTTL compatible. DIN9 is the MSB and DIN0 is the LSB. HD 20-bit mode SD/HD = LOW 20bit/10bit = HIGH Chroma data input in SMPTE mode SMPTE_BYPASS =HIGH DVB_ASI = LOW Data input in Data-Through mode SMPTE_BYPASS = LOW DVB_ASI = LOW HD 10-bit mode SD/HD = LOW 20bit/10bit = LOW SD 20-bit mode SD/HD = HIGH 20bit/10bit = HIGH High impedance in all modes. Chroma data input in SMPTE mode SMPTE_BYPASS = HIGH DVB_ASI = LOW Data input in Data-Through mode SMPTE_BYPASS = LOW DVB_ASI = LOW Forced low in DVB-ASI mode SMPTE_BYPASS = LOW DVB_ASI = HIGH SD 10-bit mode SD/HD = HIGH 20bit/10bit = LOW High impedance in all modes. 40117 - 1 November 2007 11 of 114 GS1582 Data Sheet Table 1-1: Pin Descriptions (Continued) Pin Number F3 Name DETECT_TRS Timing Non Synchronous Type Input Description CONTROL SIGNAL INPUT Signal levels are LVCMOS/LVTTL compatible. Used to select external HVF timing mode or TRS Extraction timing mode. When DETECT_TRS = LOW, the device will use timing from the externally supplied H:V:F or CEA-861 timing signals, dependent on the state of the TIM_861 pin. When DETECT_TRS = HIGH, the device will extract timing from TRS signals embedded in the supplied video stream. F4 F10 G1, H10 G2, H9 G3 RSV RSET IO_VDD IO_GND TIM_861 - Analog Non Synchronous Non Synchronous Non Synchronous - Input Input Power Input Power Input Reserved. Do not connect. An external 1% resistor connected to this input is used to set the SDO/SDO output amplitude. Power supply connection for digital I/O buffers. Connect to +3.3V or +1.8V DC digital. Ground connection for digital I/O buffers. Connect to digital GND. CONTROL SIGNAL INPUT Signal levels are LVCMOS/LVTTL compatible. Used to select external CEA-861 timing mode. When DETECT_TRS = LOW and TIM_861 = LOW, the device will use externally supplied H:V:F timing signals. When DETECT_TRS = LOW and TIM_861 = HIGH, the device will use externally supplied HSYNC, VSYNC, DE timing signals. When DETECT_TRS = HIGH, the device will extract timing from TRS signals embedded in the supplied video stream. G4 20bit/10bit Non Synchronous Input CONTROL SIGNAL INPUT Signal levels are LVCMOS/LVTTL compatible. Used to select the input data bus width. G5 DVB_ASI Non Synchronous Input CONTROL SIGNAL INPUT Signal levels are LVCMOS/LVTTL compatible. When set HIGH, the device is configured for the transmission of DVB-ASI data in SD mode (SD/HD = HIGH). When set LOW, the device will not support the encoding of DVB-ASI data. NOTE: When operating in DVB-ASI mode the SD/HD pin must be set HIGH and SMPTE_BYPASS must be set LOW. 40117 - 1 November 2007 12 of 114 GS1582 Data Sheet Table 1-1: Pin Descriptions (Continued) Pin Number G6 Name SMPTE_BYPASS Timing Non Synchronous Type Input Description CONTROL SIGNAL INPUT Signal levels are LVCMOS/LVTTL compatible. Used to enable/disable all forms of encoding/decoding, scrambling and EDH insertion. When set LOW, the device will operate in data through mode (DVB_ASI = LOW), or in DVB-ASI mode (DVB_ASI = HIGH). No SMPTE scrambling will take place and none of the I/O processing features of the device will be available when SMPTE_BYPASS is set LOW. When set HIGH, the device will perform SMPTE scrambling and I/O processing. G7 IOPROC_EN/DIS Non Synchronous Input CONTROL SIGNAL INPUT Signal levels are LVCMOS/LVTTL compatible. Used to enable or disable I/O processing features. When set HIGH, the following I/O processing features of the device are enabled: * Audio Embedding * EDH Packet Generation and Insertion (SD-only) * SMPTE 352M Packet Generation and Insertion * ANC Data Checksum Calculation * ANC Data Insertion * Line-based CRC Generation and Insertion (HD-only) * Line Number Generation and Insertion (HD-only) * TRS Generation and Insertion * Illegal Code Remapping To enable a subset of these features, set IOPROC_EN/DIS = HIGH and disable the individual feature(s) in the IOPROC_DISABLE register accessible via the host interface. When set LOW, the I/O processing features of the device are disabled, and can not be enabled by changing the settings in the IOPROC_DISABLE register. G8 RESET Non Synchronous Input CONTROL SIGNAL INPUT Signal levels are LVCMOS/LVTTL compatible. Used to reset the internal operating conditions to default settings and to reset the JTAG test sequence. Normal Mode (JTAG/HOST = LOW) When set LOW, all functional blocks will be set to default conditions and all input and output signals become high impedance including the serial digital outputs SDO and SDO. When set HIGH, normal operation of the device resumes 10usec after the low to high transition of the RESET signal. JTAG Test Mode (JTAG/HOST = HIGH) When set LOW, all functional blocks will be set to default and the JTAG test sequence will be held in reset. When set HIGH, normal operation of the JTAG test sequence resumes. 40117 - 1 November 2007 13 of 114 GS1582 Data Sheet Table 1-1: Pin Descriptions (Continued) Pin Number H3 Name ANC_BLANK Timing Non Synchronous Type Input Description CONTROL SIGNAL INPUT Signal levels are LVCMOS/LVTTL compatible. Used to enable or disable ANC data blanking. When set LOW, the HANC and VANC data is mapped to the appropriate blanking levels. H4 LOCKED Synchronous with PCLK Output STATUS SIGNAL OUTPUT Signal levels are LVCMOS / LVTTL compatible. This signal is set HIGH by the device when the internal PLL has achieved lock to the supplied PCLK signal. This pin is set LOW by the device under all other conditions. IO_VDD = 3.3V Drive Strength = 8mA IO_VDD = 1.8V Drive Strength = 4mA H5 H6 H7 GRP2_EN/DIS GRP1_EN/DIS AUDIO_INT Non Synchronous Non Synchronous Non Synchronous Input Input Output Enable Input for Audio Group 2. Enable Input for Audio Group 1. STATUS SIGNAL OUTPUT Signal levels are LVCMOS/LVTTL compatible. Summary Interrupt from Audio Processing. This signal is set HIGH by the device to indicate a problem with the audio processing which requires the Host processor to interrogate the interrupt status registers. IO_VDD = 3.3V Drive Strength = 8mA IO_VDD = 1.8V Drive Strength = 4mA H8 JTAG/HOST Non Synchronous Input CONTROL SIGNAL INPUT Signal levels are LVCMOS/LVTTL compatible. Used to select JTAG Test Mode or Host Interface Mode. When set HIGH, CS_TMS, SDOUT_TDO, SDI_TDI and SCLK_TCK are configured for JTAG boundary scan testing. When set LOW, CS_TMS, SDOUT_TDO, SDI_TDI and SCLK_TCK are configured as Gennum Serial Peripheral Interface (GSPI) pins for normal host interface operation. 40117 - 1 November 2007 14 of 114 GS1582 Data Sheet Table 1-1: Pin Descriptions (Continued) Pin Number J4 J5 J6 J7 J9 Name AIN_5/6 WCLK_2 AIN_1/2 WCLK_1 SDOUT_TDO Timing Synchronous with ACLK_2 Clock Synchronous with ACLK_1 Clock Synchronous with SCLK_TCK Type Input Input Input Input Output Description Serial Audio Input; Channels 5 and 6. 48kHz word clock for Audio Group 2. Serial Audio Input; Channels 1 and 2. 48kHz word clock for Audio Group 1. COMMUNICATION SIGNAL OUTPUT Signal levels are LVCMOS/LVTTL compatible. Serial Data Output / Test Data Output Host Mode (JTAG/HOST = LOW) This pin operates as the host interface serial output, used to read status and configuration information from the internal registers of the device. JTAG Test Mode (JTAG/HOST = HIGH) This pin is used to shift test results and operates as the JTAG test data output, TDO. NOTE: If the host interface is not being used leave this pin unconnected. IO_VDD = 3.3V Drive Strength = 12mA IO_VDD = 1.8V Drive Strength = 4mA J10 SCLK_TCK Non Synchronous Input COMMUNICATION SIGNAL INPUT Signal levels are LVCMOS/LVTTL compatible. Serial Data Clock / Test Clock. Host Mode (JTAG/HOST = LOW) SCLK_TCK operates as the host interface burst clock, SCLK. Command and data read/write words are clocked into the device synchronously with this clock. JTAG Test Mode (JTAG/HOST = HIGH) This pin is the TEST MODE START pin, used to control the operation of the JTAG test clock, TCK. NOTE: If the host interface is not being used, tie this pin HIGH. 40117 - 1 November 2007 15 of 114 GS1582 Data Sheet Table 1-1: Pin Descriptions (Continued) Pin Number K4 K5 K6 K7 K9 Name AIN_7/8 ACLK_2 AIN_3/4 ACLK_1 CS_TMS Timing Synchronous with ACLK_2 Clock Synchronous with ACLK_1 Clock Synchronous with SCLK_TCK Type Input Input Input Input Input Description Serial Audio Input; Channels 7 and 8. 3.072MHz audio clock for Audio Group 2 (channels 5-8). Serial Audio Input; Channels 3 and 4. 3.072MHz audio clock for Audio Group 1(channels 1-4). COMMUNICATION SIGNAL INPUT Signal levels are LVCMOS/LVTTL compatible. Chip Select / Test Mode Start. Host Mode (JTAG/HOST = LOW) CS_TMS operates as the host interface chip select, CS, and is active LOW. JTAG Test Mode (JTAG/HOST = HIGH) CS_TMS operates as the JTAG test mode start, TMS, used to control the operation of the JTAG test, and is active HIGH. NOTE: If the host interface is not being used, tie this pin HIGH. K10 SDIN_TDI Synchronous with SCLK_TCK Input COMMUNICATION SIGNAL INPUT Signal levels are LVCMOS/LVTTL compatible. Serial Data In / Test Data Input Host Mode (JTAG/HOST = LOW) This pin operates as the host interface serial input, SDIN, used to write address and configuration information to the internal registers of the device. JTAG Test Mode (JTAG/HOST = HIGH) This pin is used to shift and operates as the JTAG test data input, TDI. NOTE: If the host interface is not being used, tie this pin HIGH. 40117 - 1 November 2007 16 of 114 GS1582 Data Sheet 2. Electrical Characteristics 2.1 Absolute Maximum Ratings Parameter Supply Voltage, Core (CORE_VDD) Supply Voltage, Analog 1.8V (PD_VDD) Supply Voltage, I/O (IO_VDD) Supply Voltage, Analog 3.3V (CP_VDD, CD_VDD) Input Voltage Range (ACLK, WCLK, AIN, PCLK, DIN) Input Voltage Range (VCO, CP_RES, LF, RSET) Input Voltage Range (All other pins) Ambient Operating Temperature Storage Temperature Peak Reflow Temperature (JEDEC J-STD-020C) ESD Sensitivity, HBM (JESD22-A114) ESD Sensitivity, MM (JESD22-A115) NOTES: 1. Absolute Maximum Ratings are those values beyond which damage may occur. Functional operation under these conditions or at any other condition beyond those indicated in the AC/DC Electrical Characteristics sections is not implied. Value/Units -0.3V to +2.1V -0.3V to +2.1V -0.3V to +3.6V -0.3V to +3.6V -0.5V to IO_VDD+0.25V -0.5V to +3.6V -0.5V to +5.25V -40C < TA < 95C -40C < TSTG < 125C 260C 4000V 200V 2.2 Recommended Operating Conditions Table 2-1: Recommended Operating Conditions Parameter Operating Temperature Range, Ambient Supply Voltage, Digital Core Supply Voltage, Phase Detector Supply Voltage, Charge Pump Supply Voltage, Cable Driver Supply Voltage, Digital I/O Supply Voltage, Digital I/O Symbol TA CORE_VDD PD_VDD CP_VDD CD_VDD IO_VDD IO_VDD Conditions - - - - - 1.8V mode 3.3V mode Min -20 1.71 1.71 3.13 3.13 1.71 3.13 Typ 25 1.8 1.8 3.3 3.3 1.8 3.3 Max 85 1.89 1.89 3.47 3.47 1.89 3.47 Units C V V V V V V Note s 40117 - 1 November 2007 17 of 114 GS1582 Data Sheet 2.3 DC Electrical Characteristics Table 2-2: DC Electrical Characteristics Guaranteed over recommended operating conditions unless otherwise noted. Parameter System External VCO Power Supply Voltage (VCO_VDD) +1.8V Supply Current Symbol Conditions Min Typ Max Units Notes 2.375 2.5 2.625 V 1 I1V8 10/20bit HD, Audio Enabled 10/20bit HD, Audio Disabled 10/20bit SD, Audio Enabled 10/20bit SD, Audio Disabled DVB_ASI - - - - - - - - - - - - - - - - 10 138 109 112 104 100 74 74 74 74 74 491 440 445 430 424 310 125 165 130 130 120 120 86 86 86 86 86 600 540 545 530 510 - - mA mA mA mA mA mA mA mA mA mA mW mW mW mW mW mW mW 2,4 2,4 2,4 2,4 2,4 3,4 3,4 3,4 3,4 3,4 4 4 4 4 4 - 5 +3.3V Supply Current I3V3 10/20bit HD, Audio Enabled 10/20bit HD, Audio Disabled 10/20bit SD, Audio Enabled 10/20bit SD, Audio Disabled DVB_ASI Total Device Power PD 10/20bit HD, Audio Enabled 10/20bit HD, Audio Disabled 10/20bit SD, Audio Enabled 10/20bit SD, Audio Disabled DVB_ASI Reset Standby Digital I/O Input Logic LOW Input Logic HIGH Output Logic LOW VIL VIH VOL 3.3V or 1.8V operation 3.3V or 1.8V operation 1.8V mode 3.3V mode Output Logic HIGH VOH 1.8V mode 3.3V mode - 0.7 x IO_VDD - - 1.4 2.4 - - - - - - 0.3 x IO_VDD - 0.3 0.4 - - V V V V V V - - - - - - 40117 - 1 November 2007 18 of 114 GS1582 Data Sheet Table 2-2: DC Electrical Characteristics (Continued) Guaranteed over recommended operating conditions unless otherwise noted. Parameter Output Output Common Mode Voltage NOTES 1. 2. 3. 4. 5. Symbol Conditions Min Typ Max Units Notes VCMOUT 75 load, RSET=750 SD and HD mode - CD_VDD - VSDD - V - VCO_VDD guaranteed only when GO1555 is connected. Sum of all 1.8V supplies. Sum of all 3.3V supplies. IO_VDD = 3.3V. When IO_VDD = 1.8V, the current/power consumption is lower by up to 5mA/10mW. See Standby Section for details. 2.4 AC Electrical Characteristics Table 2-3: AC Electrical Characteristics Guaranteed over recommended operating conditions unless otherwise noted. Parameter System Device Latency Symbol Conditions Min Typ Max Units Notes - - - - 10-bit SD 20-bit HD DVB-ASI 10-bit SD or 20-bit HD; All Audio Disabled - - - - - - - - - 550 1065 15 27 PCLK PCLK PCLK PCLK - - - - Reset Pulse Width treset 10 - - ms 1 Parallel Input Parallel Clock Frequency Parallel Clock Duty Cycle Input Data Setup Time Input Data Hold Time fPCLK DCPCLK tsu tih - - 50% levels; 3.3V or 1.8V operation 13.5 40 2 2 - - - - 148.5 60 - - MHz % ns ns - - 4 4 Serial Audio Data Input Input Data Set-up Time Input Data Hold Time tsu tih 50% levels; 3.3V or 1.8V operation 74 74 - - - - ns ns - - Serial Digital Output Serial Output Data Rate DRSDO - - - Serial Output Swing Serial Output Rise/Fall Time 20% ~ 80% VSDD trfSDO trfSDO RSET = 750 75 load HD mode SD mode - - - 750 - 400 1.485 1.485/1.001 270 800 120 660 - - - 850 270 800 Gb/s Gb/s Mb/s mVp-p ps ps - - - - - - 40117 - 1 November 2007 19 of 114 GS1582 Data Sheet Table 2-3: AC Electrical Characteristics (Continued) Guaranteed over recommended operating conditions unless otherwise noted. Parameter Mismatch in rise/fall time Duty Cycle Distortion Overshoot Output Return Loss Serial Output Intrinsic Jitter Symbol tr,tf - - - ORL tOJ Conditions - - SD/HD=0 SD/HD=1 5 MHz - 1.485 GHz Pseudorandom and SMPTE Colour Bars HD signal Pseudorandom and SMPTE Colour Bars SD signal Min - - - - - - Typ - 1 5 3 18 35 Max 35 5 10 8 - 80 Units ps % % % dB ps Notes - 5 5 5 6 2 tOJ - 100 200 ps 3 GSPI GSPI Input Clock Frequency GSPI Input Clock Duty Cycle GSPI Input Data Setup Time GSPI Input Data Hold Time GSPI Output Data Hold Time CS low before SCLK rising edge Time between end of command word (or data in Auto-Increment mode) and the first SCLK of the following data word - write cycle Time between end of command word (or data in Auto-Increment mode) and the first SCLK of the following data word - read cycle CS high after SCLK rising edge NOTES: See 'Device Reset' on page 107, Figure 4-33. Alignment Jitter = measured from 100kHz to 148.5MHz Alignment Jitter = measured from 1kHz to 27MHz Input setup and hold time is dependent on the rise and fall time on the parallel input. Parallel clock and data with rise time or fall time greater than 500ps require larger setup and hold times. 5. Single Ended into 75 external load. 6. ORL depends on board design. The GS1582 achieves this specification on Gennum's evaluation boards. 1. 2. 3. 4. fSCLK DCSCLK - - - - - 15pF load 50% levels 3.3V or 1.8V operation 50% levels 3.3V or 1.8V operation 50% levels 3.3V or 1.8V operation - 40 1.5 1.5 1.5 1.5 37.1 - 50 - - - - - 10 60 - - - - - MHz % ns ns ns ns ns - - - - - - - - 50% levels 3.3V or 1.8V operation 148.4 - - ns - - 50% levels 3.3V or 1.8V operation 37.1 - - ns - 40117 - 1 November 2007 20 of 114 GS1582 Data Sheet 2.5 Solder Reflow Profiles The GS1582 is available in a Pb-free package. It is recommended that the Pb-free package be soldered with Pb-free paste using the reflow profile shown in Figure 2-1. Temperature 60-150 sec. 20-40 sec. 260C 250C 3C/sec max 217C 6C/sec max 200C 150C 25C Time 60-180 sec. max 8 min. max Figure 2-1: Maximum Pb-free Solder Reflow Profile 40117 - 1 November 2007 21 of 114 GS1582 Data Sheet 3. Input/Output Circuits All resistors in ohms, all capacitors in farads, unless otherwise shown. CD_VDD SDO SDO IREF Figure 3-1: Differential Output Stage (SDO/SDO) CP_RES 200 800mV Figure 3-2: Charge Pump Current Setting Resistor (CP_RES) 40117 - 1 November 2007 22 of 114 GS1582 Data Sheet VDD VDD 800 5.6K LF 5.6K 800 Figure 3-3: PLL Loop Filter VCO VDD 50 40K 50 160K 50pF Figure 3-4: VCO Input 40117 - 1 November 2007 23 of 114 GS1582 Data Sheet IO_VDD Input Pin Figure 3-5: Digital Input Pin with Weak Pull Up(>33k) (ACLK[2:1], WCLK[2:1], AIN[4:1], PCLK, DIN[19:0]) IO_VDD Input Pin Figure 3-6: 5V Tolerant Input Pin (All Other Input Pins) EN Output Pin Figure 3-7: Digital Output Pin with High Impedance Mode (LOCKED, AUDIO_INT, SDOUT_TDO) 40117 - 1 November 2007 24 of 114 GS1582 Data Sheet 4. Detailed Description 4.1 Functional Overview The GS1582 is a multi-rate serializer with an integrated cable driver and embedded audio multiplexer. When used in conjunction with the external GO1555 Voltage Controlled Oscillator, a transmit solution at 1.485Gb/s, 1.485/1.001Gb/s or 270Mb/s is realized. The device has three basic modes of operation that must be set through external device pins; SMPTE mode, DVB-ASI mode, and Data-Through mode. In SMPTE mode, the device will accept 10-bit multiplexed or 20-bit demultiplexed SMPTE compliant data at both HD and SD signal rates. By default, the device's additional processing features, including audio embedding, will be enabled in this mode. In DVB-ASI mode, the GS1582 will accept an 8-bit parallel DVB-ASI compliant transport stream on DIN[17:10]. The serial output data stream will be 8b/10b encoded with stuffing characters added as per the standard. Data-Through mode allows for the serializing of data not conforming to SMPTE or DVB-ASI streams. No additional processing will be done in this mode. In Standby mode, the device power consumption will be reduced. The serial digital output features a high impedance mode and adjustable signal swing. The output slew rate is automatically set by the SD/HD pin setting. GS1582 provides several data processing functions including generic ANC insertion, SMPTE 352M and EDH data packet generation and insertion, automatic video standards detection, and TRS, CRC, ANC data checksum, and line number calculation and insertion. These features are all enabled/disabled collectively using the external IO processing pin, but may be individually disabled via internal registers accessible through the GSPI host interface. Finally, the GS1582 contains a JTAG interface for boundary scan test implementations. 40117 - 1 November 2007 25 of 114 GS1582 Data Sheet 4.2 Parallel Data Inputs Data is clocked into the device on the rising edge of PCLK as shown in Figure 4-1. The input data format is defined by the setting of the external SD/HD, SMPTE_BYPASS, and DVB_ASI pins and may be presented in 10-bit or 20-bit format. The input data bus width is controlled by the 20bit/10bit input pin. PCLK DIN[19:0] DATA Control signal input tSU tIH Figure 4-1: PCLK to Data Timing 4.2.1 Parallel Input in SMPTE Mode When the device is operating in SMPTE mode, see SMPTE Mode on page 28, both SD and HD data may be presented to the input bus in either multiplexed or demultiplexed form depending on the setting of the 20bit/10bit input pin. In 20-bit mode, (20bit/10bit = HIGH), the input data format should be word aligned, demultiplexed luma and chroma data. Luma words should be presented on DIN[19:10] while chroma words should be presented on DIN[9:0]. In 10-bit mode, (20bit/10bit = LOW), the input data format should be word aligned, multiplexed luma and chroma data. The data should be presented on DIN[19:10]. DIN[9:0] will be high impedance in this mode. 4.2.2 Parallel Input in DVB-ASI Mode When operating in DVB-ASI mode, see DVB-ASI mode on page 34, the GS1582 must be set to 10-bit operation mode by setting the 20bit/10bit pin LOW. The device will accept 8-bit data words on DIN[17:10]. DIN17 = HIN is the most significant bit of the encoded transport stream data and DIN10 = AIN is the least significant bit. In addition, DIN19 and DIN18 will be configured as the DVB-ASI control signals INSSYNCIN and KIN respectively. See DVB-ASI mode on page 34 for a description of these DVB-ASI specific input signals. DIN[9:0] will have a Logic Level HIGH in DVB-ASI mode. 40117 - 1 November 2007 26 of 114 GS1582 Data Sheet 4.2.3 Parallel Input in Data-Through Mode When operating in Data-Through mode, see Data-Through Mode on page 35, the GS1582 passes data from the parallel input bus to the serial output without performing any encoding or scrambling. The input data bus width is controlled by the setting of the 20bit/10bit pin. 4.2.4 Parallel Input Clock (PCLK) The frequency of the PCLK input signal required by the GS1582 is determined by the input data format. Table 4-1 below lists the possible input signal formats and their corresponding parallel clock rates. Note that the DVB-ASI input will only be in 10-bit format, when setting the 20bit/10bit pin LOW. Table 4-1: Parallel Data Input Format Control Signals Input Data Format DIN [19:10] DIN [9:0] PCLK 20bit/ 10bit SD/ HD SMPTE_BYPASS DVB_ASI SMPTE MODE 20-bit DEMULTIPLEXED SD 10-bit MULTIPLEXED SD 20-bit DEMULTIPLEXED HD LUMA LUMA / CHROMA LUMA CHROMA HIGH IMPEDANCE CHROMA 13.5MHz 27MHz 74.25 or 74.25/ 1.001MHz LUMA / CHROMA HIGH IMPEDANCE 148.5 or 148.5/ 1.001MHz LOW LOW HIGH LOW HIGH LOW HIGH HIGH HIGH LOW HIGH HIGH HIGH LOW LOW LOW 10-bit MULTIPLEXED HD DVB-ASI MODE 10-bit DVB-ASI DVB-ASI DATA HIGH IMPEDANCE 27MHz LOW LOW HIGH HIGH LOW LOW HIGH HIGH DATA-THROUGH MODE 20-bit SD 10-bit SD 20-bit HD DATA DATA DATA DATA HIGH IMPEDANCE DATA 13.5MHz 27MHz 74.25 or 74.25/ 1.001MHz 10-bit HD DATA HIGH IMPEDANCE 148.5 or 148.5/ 1.001MHz LOW LOW LOW LOW HIGH LOW HIGH HIGH HIGH LOW LOW LOW LOW LOW LOW LOW 40117 - 1 November 2007 27 of 114 GS1582 Data Sheet 4.3 SMPTE Mode The GS1582 operates in SMPTE mode when the SMPTE_BYPASS pin is set HIGH and the DVB_ASI pin is set LOW. In this mode, the parallel data will be scrambled according to SMPTE 259M or 292M, and NRZ-to-NRZI encoded prior to serialization. 4.3.1 HVF Timing In SMPTE mode, the GS1582 can automatically detect the video standard and generate all internal timing signals. The total line length, active line length, total number of lines per field/frame and total active lines per field/frame are calculated for the received parallel video. When DETECT_TRS is LOW, the video standard and timing signals are based on the externally supplied H_Blanking, V_Blanking, and F_Digital signals. These signals go to the H/HSYNC, V/VSYNC and F/DE pins respectively. When DETECT_TRS is HIGH, the video standard timing signals will be extracted from the embedded TRS ID words in the parallel input data. Both 8-bit and 10-bit TRS code words will be identified by the device. NOTE: IO processing must be enabled for the device to remap 8-bit TRS words to the corresponding 10-bit value for transmission. See Section 4.9.4.2 for more information. The GS1582 determines the video standard by timing the horizontal and vertical reference information supplied at the H/HSYNC, V/VSYNC, and F/DE input pins, or contained in the TRS ID words of the received video data. Therefore, full synchronization to the received video standard requires one complete video frame. Once synchronization has been achieved, the GS1582 will continue to monitor the received TRS timing or the supplied H, V, and F timing information to maintain synchronization. GS1582 will lose all timing information immediately following loss of H, V and F. The H signal timing should also be configured via the H_CONFIG bit of the internal IOPROC_DISABLE register as either active line based blanking or TRS based blanking. See Packet Generation and Insertion on page 68. Active line based blanking is enabled when the H_CONFIG bit is set LOW. In this mode, the H input should be HIGH for the entire horizontal blanking period, including the EAV and SAV TRS words. This is the default H timing used by the device. The timing of these signals is shown in Figure 4-2. 40117 - 1 November 2007 28 of 114 GS1582 Data Sheet PCLK LUMA DATA OUT 3FF 000 000 XYZ (eav) XYZ (eav) 3FF 000 000 XYZ (sav) XYZ (sav) CHROMA DATA OUT 3FF 000 000 3FF 000 000 H V F H_Blanking: V_Blanking: F_Digital TIMING - HD 20-BIT INPUT MODE PCLK MULTIPLEXED Y/Cr/Cb DATA OUT H V F 3FF 3FF 000 000 000 000 XYZ (eav) XYZ (eav) H_Blanking: V_Blanking: F_Digital TIMING AT EAV - HD 10-BIT INPUT MODE PCLK MULTIPLEXED Y/Cr/Cb DATA OUT H V F 3FF 3FF 000 000 000 000 XYZ (sav) XYZ (sav) H_Blanking: V_Blanking: F_Digital TIMING AT SAV - HD 10-BIT INPUT MODE PCLK CHROMA DATA OUT 3FF 000 3FF 000 LUMA DATA OUT H V F H_CONFIG = HIGH 000 XYZ (eav) 000 XYZ (SAV) H SIGNAL TIMING: H_CONFIG = LOW H_Blanking: V_Blanking: F_Digital TIMING - SD 20-BIT INPUT MODE PCLK MULTIPLEXED Y/Cr/Cb DATA OUT H V F 3FF 000 000 XYZ (eav) 3FF 000 000 XYZ (sav) H_Blanking: V_Blanking: F_Digital TIMING - SD 10-BIT INPUT MODE Figure 4-2: H_Blanking, V_Blanking, F_Digital Timing 4.3.2 CEA 861 Timing The GS1582 extracts timing information from externally provided HSYNC, VSYNC, and DE signals when CEA 861 timing mode is selected by setting DETECT_TRS = LOW and the TIM_861 = HIGH. 40117 - 1 November 2007 29 of 114 GS1582 Data Sheet Horizontal sync (H), Vertical sync (V), and Data Enable (DE) timing must be provided via the H/HSYNC, V/VSYNC and F/DE input pins. The host interface register bit H_CONFIG will be ignored in the CEA 861 input timing mode. The GS1582 will determine the EIA/CEA-861 standard and embed EAV and SAV TRS words in the output serial video stream. Video standard detection is not dependent on the HSYNC pulse width or the VSYNC pulse width and therefore the GS1582 will tolerate non-standard pulse widths. In addition, the device can compensate for up to 1 PCLK cycle of jitter on VSYNC with respect to HSYNC and sample VSYNC correctly. NOTE 1: The period between the leading edge of the HSYNC pulse and the leading edge of Data Enable (DE) must follow the timing requirements described in the EIA/CEA-861 specification. The GS1582 embeds TRS words according to this timing relationship to maintain compatibility with the corresponding SMPTE standard. NOTE 2: When CEA 861 standards 6 & 7 [720(1440)x480i] are presented to the GS1582, the device will embed TRS words corresponding to the timing defined in SMPTE 125M to maintain SMPTE compatibility. CEA 861 standards 6 & 7 [720(1440)x480i] define the active area on lines 22 to 261 and 285 to 524 inclusive (240 active lines per field). SMPTE 125M defines the active area on lines 20 to 263 and 283 to 525 inclusive (244 lines on field 1; 243 lines on field 2). Therefore, in the first field, the GS1582 adds two active lines above and two active lines below the original active image. In the second field it adds two lines above and one line below the original active image. 40117 - 1 November 2007 30 of 114 GS1582 Data Sheet 1650 Total Horizontal Clocks per line Data Enable 370 1280 Clocks for Active Video 40 110 220 clocks HSYNC Progressive Frame: 30 Vertical Blanking Lines Data Enable 720 Active Vertical Lines ~ ~ ~ ~ ~ 745 746 110 1650 clocks HSYNC ~ ~ 745 746 747 748 749 750 1 2 3 4 5 6 7 25 26 ~ ~ ~ 750 562 VSYNC Figure 4-3: HSYNC:VSYNC:DE Input Timing 1280 x 720p @ 59.94/60 2200 Total Horizontal Clocks per line Data Enable 280 1920 Clocks for Active Video 44 148 clocks 88 HSYNC Field 1: 22 Vertical Blanking Lines Data Enable 2200 clocks 88 540 Active Vertical Lines per field ~ ~ 1123 1124 1125 1 2 3 4 5 6 7 8 ~ ~ 19 20 21 ~ HSYNC ~ ~ ~ 560 561 VSYNC Field 2: 23 Vertical Blanking Lines Data Enable 88 2200 clocks 1100 540 Active Vertical Lines per field ~ HSYNC ~ ~ ~ ~ ~ 560 561 562 563 564 565 566 567 568 569 570 582 583 584 VSYNC Figure 4-4: HSYNC:VSYNC:DE Input Timing 1920 x 1080i @ 59.94/60 40117 - 1 November 2007 ~ ~ 1123 1124 1125 ~ ~ 31 of 114 GS1582 Data Sheet 1716 Total Horizontal Clocks per line Data Enable 276 38 HSYNC 124 1440 Clocks for Active Video 114 clocks Field 1: 22 Vertical Blanking Lines Data Enable 38 1716 clocks 240 Active Vertical Lines per field ~ ~ ~ 238 ~ HSYNC 524 525 1 2 3 4 5 6 7 8 9 21 22 261 262 263 VSYNC Field 2: 23 Vertical Blanking Lines Data Enable 1716 clocks 858 240 Active Vertical Lines per field ~ ~ ~ 238 ~ HSYNC 261 262 263 264 265 266 267 268 269 270 271 284 285 524 525 1 VSYNC Figure 4-5: HSYNC:VSYNC:DE Input Timing 720 (1440) x 480i @ 59.94/60 40117 - 1 November 2007 ~ ~ ~ ~ ~ ~ ~ ~ 32 of 114 GS1582 Data Sheet 1980 Total Horizontal Clocks per line Data Enable 700 1280 Clocks for Active Video 40 220 clocks 440 HSYNC Progressive Frame: 30 Vertical Blanking Lines Data Enable ~ ~ 440 1980 clocks 720 Active Vertical Lines ~ ~ HSYNC ~ ~ ~ 745 746 747 748 749 750 1 2 3 4 5 6 7 25 26 ~ 745 746 ~ ~ 750 VSYNC Figure 4-6: HSYNC:VSYNC:DE Input Timing 1280 x 720p @ 50 2640 Total Horizontal Clocks per line Data Enable 720 1920 Clocks for Active Video 44 148 clocks 528 HSYNC Field 1: 22 Vertical Blanking Lines Data Enable 2640 clocks 528 540 Active Vertical Lines per field ~ ~ 1123 1124 1125 1 2 3 4 5 6 7 8 ~ ~ 19 20 21 ~ HSYNC ~ ~ ~ 560 561 VSYNC Field 2: 23 Vertical Blanking Lines Data Enable 528 2640 clocks 1320 540 Active Vertical Lines per field ~ HSYNC ~ ~ ~ ~ ~ 560 561 562 563 564 565 566 567 568 569 570 582 583 584 VSYNC Figure 4-7: HSYNC:VSYNC:DE Input Timing 1920 x 1080i @ 50 40117 - 1 November 2007 ~ ~ 1123 1124 1125 ~ ~ 562 33 of 114 GS1582 Data Sheet 1728 Total Horizontal Clocks per line Data Enable 288 24 HSYNC 126 1440 Clocks for Active Video 138 clocks Field 1: 24 Vertical Blanking Lines Data Enable 24 1728 clocks 288 Active Vertical Lines per field ~ ~ ~ 264 ~ 22 23 HSYNC 623 624 625 1 2 3 4 5 6 7 310 311 312 VSYNC Field 2: 25 Vertical Blanking Lines Data Enable 1728 clocks 864 288 Active Vertical Lines per field ~ ~ ~ 264 ~ 335 336 HSYNC 310 311 312 313 314 315 316 317 318 319 320 623 624 625 VSYNC Figure 4-8: HSYNC:VSYNC:DE Input Timing 720 (1440) x 576 @ 50 4.4 DVB-ASI mode The GS1582 operates in DVB-ASI mode when the SMPTE_BYPASS pin is set LOW and the DVB_ASI and SD/HD pins are set HIGH. In this mode, all SMPTE processing functions are disabled, and the 8-bit transport stream data will be 8b/10b encoded prior to serialization. 4.4.1 Control Signal Inputs In DVB-ASI mode, the DIN19 and DIN18 pins are configured as DVB-ASI control signals INSSYNCIN and KIN respectively. When INSSYNCIN is set HIGH, the device will insert K28.5 sync characters into the data stream. This function is used in system implementations where the GS1582 is preceded by an external data FIFO. Parallel DVB-ASI data may be clocked into the FIFO at some rate less than 27MHz. The INSSYNCIN input may then be connected to the FIFO empty signal, providing a means of padding the data transmission rate to 27MHz. See Figure 4-9. 40117 - 1 November 2007 ~ ~ ~ ~ ~ ~ ~ ~ 34 of 114 GS1582 Data Sheet NOTE: 8b/10b encoding will take place after K28.5 sync character insertion. KIN should be set HIGH whenever the parallel data input is to be interpreted as any special character defined by the DVB-ASI standard (including the K28.5 sync character). This pin should be set LOW when the input is to be interpreted as data. NOTE: When operating in DVB-ASI mode, DIN[9:0] are set to high impedance. AIN ~ HIN TS 8 FIFO 8 SDO KIN WRITE_CLK <27MHz READ CLK =27MHz CLK_IN FIFO_EMPTY KIN INSSYNCIN GS1582 SDO CLK_OUT PCLK = 27MHz Figure 4-9: DVB-ASI FIFO Implementation using the GS1582 4.5 Data-Through Mode The GS1582 may be configured to operate as a simple parallel-to-serial converter. In this mode, the device passes data to the serial output without performing any scrambling or encoding. Data-through mode is enabled only when both the SMPTE_BYPASS and DVB_ASI pins are set LOW. 4.6 Standby Mode In standby mode, the power consumption of the GS1582 is reduced to 125mW. Standby mode is enabled when the STANDBY pin is set HIGH. Once the STANDBY pin is set HIGH, it may take up to 50ms for power reduction to take place. In this mode, the serial output pins are set to high impedance, and the GS1582 loses lock to the reference input PCLK. While in standby mode, the programmed register values are retained. However, no registers can be accessed for reading or writing via the GSPI port. No write bits will be captured and all read functions will return a value of 0. The power in standby mode can be further reduced through two means: 1. Eliminate activity on all parallel data and clock inputs. This can be achieved by setting the parallel data and clock HIGH, or not driving them. Setting the parallel inputs to LOW is not recommended as it will result in a smaller power saving. 2. Remove the 3.3V supply to the CD_VDD pin of the device. The standby power consumption under various conditions is shown in Table 4-2: Standby Power Consumption. 40117 - 1 November 2007 35 of 114 GS1582 Data Sheet In order to return to normal operation from standby mode, the STANDBY pin must be set to LOW. Once normal operation is resumed, the GS1582 will re-lock to the reference PCLK. The recovery time from standby mode is the same as initial power-up but no reset is required. Once the GS1582 re-locks to the reference PCLK, operation is resumed according to the configuration held before entering standby mode. Table 4-2: Standby Power Consumption Standby Condition STANDBY asserted STANDBY asserted Parallel data and clock inactive STANDBY asserted 3.3V supply removed from CD_VDD STANDBY asserted Parallel data and clock inactive 3.3V supply removed from CD_VDD Typical Power Consumption (mW) 125 100 35 <10 4.7 Audio Multiplexer Up to eight channels of audio may be embedded into the GS1582 video data stream in accordance with SMPTE 299M and SMPTE 272M. The audio data is input in two groups of four channels, with corresponding clock signals. The audio input signal formats supported include AES/EBU and three other industry standard serial digital formats. 16, 20 and 24-bit audio sample sizes are supported at 48kHz synchronous for SD formats and 48kHz synchronous or asynchronous for HD formats. Additional audio processing features include audio mute, individual channel enable, channel re-mapping, audio group replacement, cascade, group selection, and audio channel status insertion. The audio system clock can be provided by Gennum's GEN-ClocksTM series of clock generation IC's. In serial formats, the audio clocks required by the core are two word clocks and two signals that are a multiple of 64fs. The SD audio multiplexer core is compliant with SMPTE 272M A and C. The HD audio multiplexer core is fully compliant with SMTPE 299M. 4.7.1 Audio Core Configurations Figure 4-10 shows the top level block diagrams of both the SD and HD multiplexer cores. Each group of audio has one word clock signal and one audio clock signal. Data present at Ain_1/2 and Ain_3/4 share clocks present at WCLK1 and ACLK1, while data present at Ain_5/6 and Ain_7/8 share clocks present at WCLK2 and ACLK2. 40117 - 1 November 2007 36 of 114 GS1582 Data Sheet Audio embedding may be disabled for each group independently using the pins GRP1_EN/DIS and GRP2_EN/DIS. NOTE: Disabling a single group does not reduce the power consumption of the GS1582, however disabling both groups results in a power reduction. PCLK 10 10 LOCKED _ GRP1_EN/DIS ACLK1 WCLK1 Ain_1/2 Ain_3/4 _ GRP2_ EN/DIS ACLK2 WCLK2 Ain_5/6 Ain_7/8 _ SD/HD _ IOPROC _EN/DIS SD and HD Audio Embedding Block AUDIO_INT AUDIO_INS (From IOPROC_DIS regsiter ) _ RESET Configuration & status register read / write access Figure 4-10: Audio Multiplexer Top Level 4.7.2 Audio Detection The audio multiplexer detects the presence of audio data and control packets in any of four embedded audio groups. The presence of audio data is indicated by the ADPGx_DET bits in the host interface, while the presence of control packets is indicated by the ACPGx_DET bits in the host interface. In SD mode, the presence of extended audio data packets is indicated by the AXPGx_DET bits in the host interface. These detection flags are asserted for the duration that audio data packets are detected. For SD formats, the first Ancillary Data Flag (ADF) must always be contiguous after the EAV words. For HD formats, the first Ancillary Data Flag must always be contiguous after the two EAV CRC words. By default, the device will delete all incoming ancillary data with audio data or control packet DID's. Refer to Section 4.13.3 for HD and SD audio multiplexer status and configuration registers. 40117 - 1 November 2007 37 of 114 GS1582 Data Sheet 4.7.3 Audio Modes of Operation The audio multiplexer operates in three distinct modes: normal mode, cascade mode, and audio group replacement mode. In normal operating mode, up to two audio groups can be added to the output video. (See Table 4-3: Audio Multiplexer Modes of Operation). All existing audio packets are deleted from the video input, however arbitrary packets, SDTI packets and SMPTE 352M packets are not deleted. When the EN_CASCADE host interface bit is set HIGH, the audio multiplexer operates in cascade mode. Up to two audio groups can be added to the video output. The added groups will not replace existing embedded audio groups. No existing packets are deleted from the video input, and the added audio packets are appended to the last packet in the video input. In cascade mode, if the audio multiplexer is configured to add group 1 audio data packets with the same group number as an existing group, MUX_ERRA will be asserted in the host interface. Similarly, MUX_ERRB will be asserted if the configuration leads to replacing existing groups with group 2. When the AGR bit in the host interface is set HIGH, the audio multiplexer operates in group replacement mode. In this mode, added audio groups can replace existing embedded audio groups. The embedded audio groups will be sorted by audio group number. No packets will be deleted from the video input (except for the audio packets being replaced). SDTI packets and SMPTE 352M packets are placed before the audio packets, and arbitrary packets are placed after the audio packets in SD mode. NOTE 1: When audio group replacement mode is selected, the cascade function is disabled. NOTE 2: In normal SD mode, if the incoming stream has a completely full HANC space, the outgoing HANC space will only get filled with up to 235 words and the remainder of the space is left blank. This will not occur if there are one or more words free in the incoming HANC space. NOTE 3: SD audio in cascade mode may only be inserted if the HANC space of the incoming stream is not completely full. If the incoming stream has a full HANC space, audio packets will be inserted beyond the HANC boundary. The space following the inserted audio packets will then be blanked until the next EAV is detected in the video stream. This will not occur if there are two or more words free at the end of the incoming HANC space after the existing packets. NOTE 4: HD audio in normal mode may only be inserted if the HANC space of the incoming stream is not completely full. If the incoming stream has a full HANC space, packets will be inserted beyond the HANC boundary. The space following the inserted packets will then be blanked until the next EAV is detected in the video stream. This will not occur if there are two or more words free at the end of the incoming HANC space after the existing packets. 40117 - 1 November 2007 38 of 114 GS1582 Data Sheet Table 4-3: Audio Multiplexer Modes of Operation Host Interface Registers EN_CASCADE = 0, AGR = 0 EN_CASCADE = 1, AGR = 0 EN_CASCADE = 0, AGR = 1 EN_CASCADE = 1, AGR = 1 Operating Mode Normal Mode Cascade Mode Audio Group Replacement Mode Audio Group Replacement Mode 4.7.4 Audio Packet Delete Ancillary data packets with non-audio data ID words, such as arbitrary, EDH, SDTI header and SMPTE 352M, will not be deleted from the data stream. On lines where SMPTE 352M or SDTI header packets exist, the audio data packets must be contiguous to the 352M and SDTI packets in SD mode. For HD formats, the audio data packets must always be contiguous after the two EAV CRC words. If this is not the case, all existing audio data and control packets will be deleted. When the EN_CASCADE host interface bit is set HIGH, all existing audio data and control packets will remain in the video stream. When the AGR bit in the host interface is set HIGH, audio group replacement mode is selected. In this mode, existing audio data and control packets will not be deleted from the data stream with the exception of any packets of groups being replaced. In cases where the ADF is not placed immediately after the CRC or EAV words, or there are gaps between the packets, the audio core will delete all existing audio data and control packets, regardless of the EN_CASCADE or AGR setting. Figure 4-11 shows an example of correct and incorrect placement of ancillary data packets for a SD format. 352M / SDTI Packet Audio Group 1 Audio Group 2 EAV Blank Correct placement of Ancillary Data within HANC Space 352M / SDTI Packet Audio Group 1 Audio Group 2 EAV Blank Blank Blank HANC with space between EAV and Ancillary Data (Audio Packets will be deleted) Figure 4-11: Ancillary Data Packet Placement Example 40117 - 1 November 2007 39 of 114 SAV SAV GS1582 Data Sheet 4.7.5 Arbitrary, SMPTE 352M & EDH Packet Detect The audio multiplexer detects the presence of any arbitrary data packets. If present, these packets will be removed and stored for re-insertion after audio packets have been embedded. If there is insufficient HANC space available, the arbitrary data packet will be discarded. To detect the arbitrary data packet, the audio core looks for any ancillary data packets which have a DID other than audio, extended audio, control, SDTI header, SMPTE 352M or EDH packets. Arbitrary data packets and formatting are defined in SMPTE 291M. Arbitrary data packets are only present on the luma channel of the HD video input. All EDH processing is carried out following the audio core, as the CRC's will require updating. The audio core detects the presence of EDH packets in the HANC region. These packets are preserved and re-embedded after multiplexing of audio packets, according to RP 165. The audio core does not perform EDH CRC calculation and flag updates. Since the audio core multiplexes audio packets on to lines where the ancillary data packet containing EDH checkwords and status flags is to be placed (lines 9 and 272 in 525, and lines 5 and 318 in 625), if there is insufficient horizontal ancillary data space available after audio multiplexing, the EDH block will overwrite audio packets. This problem may occur in both 525 and 625 when 16 channels (4 audio groups) of 24-bit audio are embedded. NOTE 1: The audio sample distribution used by the SD audio core for both 525 and 625 will increase the available space in the horizontal ancillary data space. NOTE 2: Due to the large size of the horizontal ancillary data space in 720p/24, 720p/25 and 720p/30 video standards, the maximum number of ancillary data words the audio core can process is limited to 1024 when configured to these standards. Table 4-4 lists the data ID's and packet lengths for arbitrary, EDH, SDTI header and SMPTE 352M packets. When the presence of a SMPTE 352M packet is detected, the audio core extracts and stores the packet for re-insertion. Audio data packets will always be placed after the SMPTE 352M packet. Table 4-4: Non-audio Ancillary Data Packet DIDs Ancillary Data Packet Arbitrary (SMPTE 291M) EDH (RP 165) Payload Identifier (SMPTE 352M) SDTI Header (SMPTE 305M) DID User 1F4h 241h 140h SDID User - 101h 101h Packet Length (Words) 262 max 23 11 53 40117 - 1 November 2007 40 of 114 GS1582 Data Sheet NOTE: When serializing SDTI signals, it is recommended that the user ensure there are no SMPTE 352M packets present in the input video data. 4.7.6 Audio Packet Multiplexing The SD core places audio data packets contiguously after the EAV. Any Extended Audio Data Packets are placed immediately following the Audio Data Packet of the same audio group. The HD core places audio data packets contiguously after the two line CRC words. In cases where the SMPTE 352M packet or SDTI header are present after the EAV or CRC, the audio data will be placed contiguously from the 352M or SDTI header packets. On lines where the 352M or SDTI header packets are present, there may be insufficient HANC space for embedding 4 audio groups. If there is insufficient HANC space available, the 352M or SDTI header packets are always re-inserted and the remaining audio group packet to be inserted is discarded. On lines where the EDH packet is present, the audio data will be embedded up to the point reserved for the EDH packet. If there is insufficient HANC space available, the EDH packet is always re-inserted and the audio data packet discarded. In the case where there is insufficient room in the HANC space to embed the selected audio data packets, the multiplexer core will delete any arbitrary data packets. If there is still insufficient room in the HANC space, the multiplexer core will not embed audio data packets. 4.7.7 Audio Insertion After Video Switching Point 4.7.7.1 SD Formats The switching lines for SD formats are defined in SMPTE RP 168 as lines 10 and 273 for 525-line based formats, and lines 6 and 319 for 625-line based formats. The audio core does not place any audio data or control packets in the line immediately after the video switching line. For example, with the standard switch point of line 10 for field 1 in 525, there will be no audio data or control packets on line 11. The next packets will appear on line 12. 4.7.7.2 HD Formats The video switching lines for HD formats are defined in SMPTE 299M as lines 7 and 569. The audio core does not place any audio data or control packets in the line immediately after the video switching point. For example, with the standard switch point of line 7 for field 1, there will be no audio data packets in line 8. The next packets will appear on line 9. The audio control packets will be multiplexed once per field, two lines after the video switch point, on lines 9 and 571. 40117 - 1 November 2007 41 of 114 GS1582 Data Sheet 4.7.8 Audio Data Packets 4.7.8.1 SD Formats Figure 4-12 shows the structure of the SD audio data packet as defined in SMPTE 272M. Table 4-5 lists the descriptions of the audio data packet words. The audio core automatically generates certain audio data packet words, as shown in Table 4-5. Audio Sample Words 10-bit DBN CH1 CH2 CH3 CH4 CH3 ADF CH4 X X+1 X+2 DID DC X X+1 X+2 X X+1 X+2 X X+1 X+2 X X+1 X+2 X X+1 X+2 Figure 4-12: SD Audio Data Packet Structure Table 4-5: Audio Data Packet Word Descriptions Name ADF No. of Words 3 Description Ancillary Data Flag Data 000h 3FFh 3FFh 2FFh 1FDh 1FBh 2F9h Repeat 1-255 - - - - - - Auto-Generation Yes DID 1 Audio Group Data ID See Table 4-10 DBN DC CH1 CH2 CH3 CH4 CS 1 1 4 4 4 4 1 Data Block Number Data Count Channel 1 ancillary data words Channel 2 ancillary data words Channel 3 ancillary data words Channel 4 ancillary data words Checksum Yes Yes Yes Figure 4-13 shows the structure of the extended audio data packets as defined in SMPTE 272M. Table 4-6 lists the descriptions of the extended audio data packet words. The audio core automatically generates certain audio data packet words. The extended audio data packet is embedded immediately after the audio data packet with same group DID. 40117 - 1 November 2007 42 of 114 CS GS1582 Data Sheet Extended Audio 10-bit DBN AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX ECC4 AUX ECC5 ADF DID DC Figure 4-13: SD Extended Audio Data Packet Structure Table 4-6: Extended Audio Data Packet Word Descriptions Name ADF No. of Words 3 Description Ancillary Data Flag Data 000h 3FFh 3FFh 1FEh 2FCh 2FAh 1F8h Repeat 1-255 - - - Auto-Generation Yes DID 1 Audio Group Data ID See Table 4-10 DBN DC AUX CS 1 1 4 1 Data Block Number Data Count Auxiliary data from one channel pair words Checksum Yes Yes Yes For both audio data and extended audio packets, the Data Block Number is embedded with a running sequence of 1 to 255. 4.7.8.2 HD Formats Figure 4-14 shows the structure of the audio data packets as defined in SMPTE 299M. The audio data packets are multiplexed into the chroma channel of the video data stream. Table 4-7 lists the descriptions of the audio data packet words. The audio core automatically generates certain audio data packet words, as shown in Table 4-7. User Data Words ECC0 ECC1 ECC2 ECC3 10-bit DBN ADF CH1 CH2 CH3 CH4 CLK DID DC ECC Protected Figure 4-14: HD Audio Data Packet Structure 40117 - 1 November 2007 43 of 114 CS CS GS1582 Data Sheet Table 4-7: Audio Data Packet Word Descriptions Name ADF No. of Words 3 Description Ancillary Data Flag Data 000h 3FFh 3FFh 2E7h 1E6h 1E5h 2E4h Repeat 1-255 218h - - - - - - - Auto-Generation Yes DID 1 Audio Group Data ID See Table 4-10 DBN DC CLK CH1 CH2 CH3 CH4 ECC0-5 CS 1 1 2 4 4 4 4 6 1 Data Block Number Data Count Audio Clock Phase Data Channel 1 ancillary data words Channel 2 ancillary data words Channel 3 ancillary data words Channel 4 ancillary data words Error correction code for lower 8 bits of first 24 words Checksum. Calculates the sum of lower 9 bits of 22 words from DID Yes Yes Yes Yes Yes 40117 - 1 November 2007 44 of 114 GS1582 Data Sheet 4.7.9 Audio Control Packets 4.7.9.1 SD Formats In SD mode, the control packets are inserted in the first line after the blanking line, and following the audio data packets. Figure 4-15 shows the structure of the SD audio control packet as defined in SMPTE 272M. An audio control packet is multiplexed once per field in the video data stream. Table 4-8 lists descriptions of the audio control packet words. The audio core automatically generates certain audio control packet words. User Data Words DELC0-3 DELD0-3 DELA0-3 DELB0-3 RSRV RSRV AF1-2 AF3-4 RATE 10-bit DBN ADF ACT DID DC Figure 4-15: SD Audio Control Packet Structure Table 4-8: Audio Control Packet Word Descriptions Name ADF No. of Words 3 Description Ancillary Data Flag Data 000h 3FFh 3FFh 1EFh 2EEh 2EDh 1ECh Repeat 1-255 - - - - - - - - - Auto-Generation Yes DID 1 Audio Group Data ID See Table 4-10 DBN DC AF1-2 AF3-4 RATE ACT DELA0 -3 DELB0 -3 DELC0 -3 DELD0 -3 1 1 1 1 1 1 3 3 3 3 Data Block Number Data Count Ch1/2 Audio Frame Number Ch3/4 Audio Frame Number Sampling Frequency Active Channel Ch1/Ch1&2 Delay Data Ch3/Ch3&4 Delay Data Ch2 Delay Data Ch4 Delay Data Yes Yes Yes Same as AF1-2 Yes ACT[8:1] setting 27-bit Host Interface setting 27-bit Host Interface setting 27-bit Host Interface setting 27-bit Host Interface setting 40117 - 1 November 2007 CS 45 of 114 GS1582 Data Sheet Table 4-8: Audio Control Packet Word Descriptions (Continued) Name RSRV CS No. of Words 2 1 Description Reserved Words Checksum. Calculates the sum of lower 9 bits of 22 words from DID Data 200h - Auto-Generation Yes Yes 4.7.9.2 HD Formats In HD mode, the control packets are inserted in the first line after the blanking line in the Luma channel in the first available space. Figure 4-16 shows the structure of the HD audio control packet as defined in SMPTE 299M. An audio control packet is multiplexed once per field in the luma channel of the video data stream. Table 4-9 lists descriptions of the individual audio control packet words. The audio core automatically generates certain audio control packet words. User Data Words DEL1-2 DEL3-4 RSRV RATE 10-bit DBN ADF ACT DID DC Figure 4-16: HD Audio Control Packet Structure Table 4-9: Audio Control Packet Word Descriptions Name ADF No. of Words 3 Description Ancillary Data Flag CS AF Data 000h 3FFh 3FFh 1E3h 2E2h 2E1h 1E0h 200h 10Bh - - - - Auto-Generation Yes DID 1 Audio Group Data ID See Table 4-10 DBN DC AF RATE ACT DELA0-3 1 1 1 1 1 3 Data Block Number Data Count Audio Frame Number Sampling Frequency Active Channel Ch1/2 Delay Data Yes Yes Yes Yes ACT[8:1] setting 27-bit Host Interface setting 40117 - 1 November 2007 46 of 114 GS1582 Data Sheet Table 4-9: Audio Control Packet Word Descriptions (Continued) Name DELB0-3 RSRV CS No. of Words 3 2 1 Description Ch3/4 Delay Data Reserved Words Checksum. Calculates the sum of lower 9 bits of 15 words from DID Data - 200h - Auto-Generation 27-bit Host Interface setting Yes Yes 4.7.9.3 Audio Control Packet Insertion To multiplex audio control packets for audio group 1 channels 1 to 4 (inputs Ain_1/2 and Ain_3/4), the CTRA_ON bit of the host interface must be set HIGH. To multiplex audio control packets for audio group 2 channels 5 to 8 (inputs Ain_5/6 and Ain_7/8), the CTRB_ON bit must be set HIGH. In addition, the multiplexer will only embed or replace group 1 control packets if one or more of ACT1, ACT2, ACT3 and ACT4 are set. Similarly, group 2 control packets will only be embedded or replaced if ACT5, ACT6, ACT7 or ACT8 are set. By default, the audio control packets are embedded. The audio frame sequence is also embedded for 29.97fps video standards. Setting the AFNA_AUTO and AFNB_AUTO bits in the host interface LOW disable the audio frame sequence insertion. When set LOW, the audio frame number will be set to zero (200h). The RATE word is always set to zero to denote 48kHz audio only. Control packet data can be programmed via the corresponding registers in the host interface. Refer to Section 4.13.3 for HD and SD audio multiplexer status and configuration registers. 4.7.10 Setting Packet DID The audio group DID for audio group 1 input channels 1 to 4 (Ain_1/2 and Ain_3/4) is set in the IDA[1:0] bits of the host interface. The audio group DID for audio group 2 input channels 5 to 8 (Ain_5/6 and Ain_7/8) is set in IDB[1:0] of the host interface. Table 4-10 shows the 2-bit host interface setting for the corresponding audio group DID. For 24-bit audio support using the SD core, the extended audio group DID for audio group 1 input channels 1 to 4 is set to the same group in IDA[1:0] of the host interface. The extended audio group DID for audio group 2 input channels 5 to 8 is set to the same group in IDB[1:0] of the host interface. 24-bit support is selected by setting the 24BIT bit of host interface HIGH. When the host interface CASCADE bit is set LOW, the audio core defaults to audio groups 1 and 2, where Ain_1/2 and Ain_3/4 are multiplexed with audio group 1 DID, and Ain_5/6 and Ain_7/8 with audio group 2 DID. 40117 - 1 November 2007 47 of 114 GS1582 Data Sheet Table 4-10: Audio Group DID Host Interface Settings Audio Group SD Data DID SD Extended DID HD Data DID SD Control DID HD Control DID Host Interface Register Setting (2-bit) 00b 01b 10b 11b 1 2 3 4 2FFh 1FDh 1FBh 2F9h 1FEh 2FCh 2FAh 1F8h 2E7h 1E6h 1E5h 2E4h 1EFh 2EEh 2EDh 1ECh 1E3h 2E2h 2E1h 1E0h Table 4-11: Audio Data and Control Packet DID Setting Register Name Description Default CASCADE set LOW 00b 01b Default CASCADE set HIGH 10b 11b IDA[1:0] IDB[1:0] Group 1 audio data and control packet DID setting Group 2 audio data and control packet DID setting When the CASCADE bit is set HIGH, the GS1582 defaults to audio groups 3 and 4, where Ain_1/2 and Ain_3/4 are multiplexed with audio group 3 DID, and Ain_5/6 and Ain_7/8 with audio group 4 DID. NOTE: If IDA and IDB are set to the same value, these bits will automatically revert to their default values. Any other configurations can be programmed for the audio groups as required. 4.7.11 Audio Group Replacement Audio group replacement mode allows the multiplexing of new audio groups, whilst replacing existing embedded audio with the same group DID. All other embedded audio groups will remain in the video stream. Up to two groups of audio (and extended audio for SD formats) can be replaced at once. The first function performed by the GS1582 is deleting the audio group or groups to be replaced. The next step is removing and storing any other audio packets that are to be preserved. The final step is to embed the new and stored audio data packets so they are contiguous from the EAV (for HD formats, they will be contiguous after the line CRC words). See Figure 4-17. 40117 - 1 November 2007 48 of 114 GS1582 Data Sheet On lines where the SMPTE 352M packet is already present, the audio core places new and existing audio data packets contiguously after the 352M packets. For HD formats, the 352M packets are embedded in the luma channel of the video data stream; therefore, no audio data packets will be placed after the 352M packets. Audio Group 1 Audio Group 2 Audio Group 3 Audio Group 4 CRC EAV Blank (200h) Video Signal Input to Audio Core (with existing Audio Data Packets) Audio Group 3 Audio Group 4 CRC EAV Blank (200h) Blank (200h) Video Signal after deleting Audio Groups 1 & 2 (ONE_AGR = 0) CRC EAV Blank (200h) Video Signal after Audio Groups 3 & 4 stored in RAM Audio Group 2 (New) Audio Group 1 (New) Audio Group 3 (Old) Audio Group 4 (Old) CRC EAV Blank (200h) Video Signal Output after replacement of Audio Groups 1 & 2 Figure 4-17: Audio Group Replacement Example (HD Formats) Audio group replacement mode is selected by setting the AGR bit of the host interface HIGH. By default, the GS1582 replaces two audio groups with their DID set in IDA[1:0] and IDB[1:0]. To replace only one audio group, with group DID set in IDA[1:0], set the ONE_AGR bit in the host interface HIGH. The audio control packets, if present, will not be replaced unless the CTR_AGR host interface bit is set HIGH. The audio control packet information will be replaced with data programmed in the associated registers in the host interface. See Audio Control Packets on page 45. Refer to Section 4.13.3 for HD and SD multiplexer core status and configuration registers. 40117 - 1 November 2007 49 of 114 SAV LN SAV LN SAV LN SAV LN GS1582 Data Sheet 4.7.12 Channel and Group Activation Multiplexing of individual audio channels is enabled by setting the ACTn bits in host interface register 0Ch. When set HIGH, the corresponding audio channel is multiplexed into the video data stream. Channels designated as not active (ACTn set LOW) will be embedded with null samples (all bits set to zero). When all ACTn bits are set LOW, no audio data packets will be multiplexed. When ACT[1-4] are set LOW, the audio group set in IDA[1:0] will not be multiplexed. Similarly, when ACT[5-8] are set LOW, the audio group set in IDB[1:0] will not be multiplexed. This allows four channel, single group operation. By default, all audio channels are enabled. Refer to Section 4.13.3 for HD and SD audio multiplexer status and configuration registers. 4.7.13 ECC Error Detection & Correction (HD Mode Only) The GS1582 will generate the error detection and correction fields in the audio data packets. All generated error detection and correction complies with SMPTE 299M. 4.7.14 Interrupt Control The GS1582 can be programmed to assert the interrupt signal (AUDIO_INT, pin H7) whenever an internal interrupt condition exists. To enable a particular type of interrupt, the corresponding bit in the host interface must be set. If the audio interrupt bit is un-masked, and the interrupt condition is met, the the AUDIO_INT pin will go HIGH. For example, if the EN_ADPG_1 is enabled, and the incoming video has embedded audio in group one, then the AUDIO_INT pin will go HIGH. Please refer to Section 4.13.3 for HD and SD audio multiplexer status and configuration registers for a complete listing of the audio interrupts. 4.7.15 Audio Clocks The audio multiplexer has 4 clock inputs: ACLK_1, ACLK_2, WCLK_1 and WCLK_2. For serial audio input modes ACLK_1/2 must be provided at 64fs, where fs is the fundamental sampling frequency of 48kHz. An audio word clock at 48kHz must also be supplied at the WCLK_1/2 inputs. For AES/EBU audio input mode, the ACLK_1/2 and WLCK_1/2 inputs are not required. All required clocks will automatically be derived from the AES/EBU preambles. ACLK_1/2 and WCLK_1/2 will be HIGH impedance in AES/EBU audio input mode. 40117 - 1 November 2007 50 of 114 GS1582 Data Sheet Table 4-12: GS1582 Serial Audio Data Inputs Parameter Input Data Set-up Time Input Data Hold Time Symbol tSU tIH Conditions 50% levels; 3.3V or 1.8V operation Min 74 74 Typ - - Max - - Units ns ns ACLK A_IN_[8/7:2/1] DATA DATA Control signal input tSU tIH Figure 4-18: ACLK to Data & Control Signal Input Timing 4.7.16 5-frame Sequence Detection 5-frame sequence detection is required for 525-line based standard definition formats and to embed the Audio Frame Number word in the audio control packets for synchronous audio in both HD and SD formats. 4.7.16.1 SD Audio Multiplexing The GS1582 detects the frame sequence that describes the sample distribution for synchronous audio. This information is used in the generation of the Audio Frame Number (AFN) field, describing the position of the current frame within the sequence. AFN values will only be generated for group A if the AFNA_AUTO bit in the host interface, and for group B if the AFNB_AUTO bit is set. If the GS1582 is not configured to generate AFN values, the AFN field will be set to 0 at all times. However, if the core is configured to generate AFN values, the AFN value will be between 1 and 5, depending on where the given frame lies in the frame sequence. With a frame rate of 25 Hz, each frame will contain 1920 samples, and each frame will have an AFN of one (see Table 4-13). For a frame rate of 29.97 Hz, 8008 samples are distributed over 5 frames, as shown in Table 4-14. The GS1582 will add the offset specified in the AFN_OFS[2:0] host interface field to the generated AFN. The result will wrap around, leaving the resulting AFN in the range of 1 through 5. 40117 - 1 November 2007 51 of 114 GS1582 Data Sheet 4.7.16.2 HD Audio Multiplexing If the ASXA bit of the host interface is set to asynchronous audio, the GS1582 will set the AFN of the group 1 control packets to zero. The GS1582 will also set the AFN of the group 1 control packets to zero if the AFNA_AUTO bit in the host interface is not set. The same relationship holds for the ASXB and AFNB_AUTO bits for group 2. The GS1582 will detect video standards with 29.97 and 59.94 frame rates by using the 5-frame sequence detect block. If a 5-frame sequence is detected, the Audio Frame Number word in the audio control packets will be embedded with the running sequence 1 through 5. The GS1582 will add the offset specified in the AFN_OFS[2:0] host interface field to the generated AFN. The result will wrap around, leaving the resulting AFN in the range of 1 through 5. In cases where each frame has the same number of samples, the Multiplexer will set the AFN to zero for every frame. These cases are shown in Table 4-13. In cases where each frame has a different number of samples, the sequences shown in Table 4-14 are used. Table 4-13: Frame Rates with AFN = 0 Frame Rate (fps) 30 25 60 24 23.98 Samples per Video Frame 1600 1920 800 2000 2002 Table 4-14: Frame Rates with varying samples per frame Frame Rate (fps) 29.97 59.94 NOTES: 1. AFNs are assuming AFN_OFS = 0. Samples, AFN = 11 1602 801 Samples, AFN = 21 1601 800 Samples, AFN = 31 1602 801 Samples, AFN = 41 1601 801 Samples, AFN = 51 1602 801 4.7.17 Audio Input Format The GS1582 accepts two audio input formats, AES/EBU digital audio input and serial digital audio input, as listed in Table 4-15. The serial audio input can be formatted in the following five modes: 40117 - 1 November 2007 52 of 114 GS1582 Data Sheet * * * * * I2S Left Justified; MSB first Left Justified; LSB first Right Justified; MSB first Right Justified; LSB first The audio input format for each audio group is configured using the AMA[1:0] (group 1 channels 1 and 2/Stereo Pair A), AMB[1:0] (group 1 channels 3 and 4/Stereo Pair B), AMC[1:0] (group 2 channels 5 and 6/Stereo Pair C), and AMD[1:0] (group 2 channels 7 and 8/Stereo Pair D) host interface registers. The default audio mode is I2S input. For serial input formats, MSB first is default, and LSB first is available via the LSB_FIRSTx bit in the host interface. NOTE: Since the audio clocks are common to all channels within one group, all channels in each group of four must be the same format. However there is no restriction on the format of different channels in one group when audio is in AES/EBU format. Also, the audio format of each group may be different. Table 4-15: Audio Input Formats AMx[1:0] 00 01 01 10 10 11 LSB_FIRSTx 0 0 1 0 1 0 Audio Output Format AES/EBU audio input Serial audio input: Left justified; MSB first Serial audio input: Left justified; LSB first Serial audio input: Right justified; MSB first Serial audio input: Right justified; LSB first I2S serial audio input (Default) 4.7.17.1 AES/EBU Mode In AES/EBU input mode, the audio sample bit rate of 64fs (3.072MHz) is effectively doubled by the bi-phase mark encoding, resulting in an effective input data rate at 128fs (6.144MHz). The AES/EBU sub-frame formatting is shown in Figure 4-19 below. 40117 - 1 November 2007 53 of 114 GS1582 Data Sheet 0 34 LSB 24-bit Audio Sample Word 27 28 29 30 31 MSB V U C P 24 -bit Sync Preamble 0 34 Aux Data 78 LSB 20-bit Audio Sample Word 27 28 29 30 31 MSB V U C P 20-bit Sync Preamble 0 34 Aux Data 78 Set To Zero 11 12 LSB 16-bit Audio Sample Word 27 28 29 30 31 MSB V U C P 16-bit Sync Preamble Validity Bit User Data Bit Channel Status Bit Parity Bit Figure 4-19: AES/EBU Sub-frame Formatting The audio clock to data timing and input format is shown in Figure 4-20. AIN 0 1 2 3 4 5 6 7 8 LSB 27 28 29 U 30 C 31 P 0 1 2 3 4 5 6 7 8 LSB 27 28 29 U 30 C 31 P Preamble AUX MSB V Preamble AUX MSB V Figure 4-20: AES/EBU Audio Input Format NOTE: Due to the bi-phase mark encoding used in AES/EBU mode, for each logic 1 bit period, there will be an additional transition. In Figure 4-20, this additional transition is not shown. In the event of a parity error in Stereo Pair A in AES/EBU mode, the GS1582 will set the AES_ERRA bit in the host interface. The same is true of AES_ERRB for Stereo Pair B, AES_ERRC for Stereo Pair C, and AES_ERRD for Stereo Pair D. NOTE: In order to read back the parity error bits of register 1, register 2 must be read first to trigger an update of these bits. The parity error bits will be cleared when read from register 1. 4.7.17.2 Serial Audio Input Mode In serial audio input modes, the GS1582 clocks the audio data input on the rising edge of the ACLK_1/2 input clock at 64fs (3.072MHz), as shown in Figure 4-21, Figure 4-24 and Figure 4-25 below. WCLK ACLK AIN 23 MSB 22 21 6 5 4 3 2 1 0 LSB 23 MSB 22 21 6 5 4 3 2 1 0 LSB Channel A (Left) Channel B (Right) Figure 4-21: Serial Audio Input: Left Justified; MSB First 40117 - 1 November 2007 54 of 114 GS1582 Data Sheet WCLK ACLK AIN 0 LSB 1 2 17 18 19 20 Channel A (Left) Channel B (Right) 21 22 23 MSB 0 LSB 1 2 17 18 19 20 21 22 23 MSB Figure 4-22: Serial Audio Input: Left Justified; LSB First WCLK ACLK AIN Channel A (Left) Channel B (Right) 23 MSB 22 21 20 19 18 17 2 1 0 LSB 23 MSB 22 21 20 19 18 17 2 1 0 LSB Figure 4-23: Serial Audio Input: Right Justified; MSB First WCLK ACLK AIN Channel A (Left) Channel B (Right) 0 LSB 1 2 3 4 5 6 21 22 23 MSB 0 LSB 1 2 3 4 5 6 21 22 23 MSB Figure 4-24: Serial Audio Input: Right Justified; LSB First WCLK ACLK AIN 23 MSB 22 7 6 5 4 Channel A (Left) Channel B (Right) 3 2 1 0 LSB 23 MSB 22 7 6 5 4 3 2 1 0 LSB Figure 4-25: I2S Audio Input 4.7.18 Audio Channel Status Input The Audio Channel Status block information can be programmed via the host interface using the ACSR[183:0] register (see Table 4-17: Audio Channel Status Information Register Settings). The Audio Channel Status input consists of 24 bytes transmitted 1 bit per audio sample over a 192-frame sequence. The same audio channel status information is embedded for each sample in an audio frame, over all 8 input channels. The GS1582 generates the Z bit to denote the start of the Audio Channel Status block. When the ACS_REGEN bit in the host interface is set HIGH, the GS1582 will use the Audio Channel Status information programmed in the ACSR[183:0] register to replace the Audio Channel Status block in all eight channels. The CRC for the Audio Channel Status block will be calculated automatically. The GS1582 will use this new Audio Channel Status information only when ACS_APPLY is HIGH and a new status boundary at this point. When the ACS_APPLY is set, the APPLY_WAITA host interface bit will be asserted until a status boundary for audio 40117 - 1 November 2007 55 of 114 GS1582 Data Sheet group 1 occurs. Similarly, APPLY_WAITB will be asserted starting when ACS_APPLY is set, and ending when a status boundary for audio group 2 occurs. Table 4-16 shows the default settings for the Audio Channel Status block. The GS1582 automatically generates the CRC byte. Table 4-16: Audio Channel Status Block Default Settings Name PRO Emphasis Sample Frequency Channel Mode AUX Byte 0 0 0 1 2 Bit 0 2-4 6-7 0-3 0-2 Default 1b 100b 01b 0001b 000b 001b Mode Professional use of channel status block None. Receiver manual override disabled 48kHz. Manual override or auto disabled Two channels. Manual override disabled SD Mode: Maximum audio word length is 20 bits HD Mode: Maximum audio word length is 24 bits Maximum word length (based on AUX setting). 24-bit for HD formats; 20-bit for SD formats Source Word Length 2 3-5 101b Table 4-17: Audio Channel Status Information Register Settings Name ACSR[7-0] ACSR[15-8] ACSR[23-16] Description Audio channel status block byte 0 set Audio channel status block byte 1 set Audio channel status block byte 2 set Default 85h 08h 28h (SD) 2Ch (HD) ACSR[31-24] ACSR[183-176] Audio channel status block set for bytes 3 to 22 00h 4.7.19 Audio Crosspoint The audio crosspoint allows any single input channel to be embedded as one or more of the 8 embedded audio channels. The default setting is for one-to-one mapping, where Ain_1/2 is embedded as Ch1 and Ch2, Ain_3/4 is embedded as Ch3 and Ch4, and so on. The same audio channel cannot be used in both group 1 and 2 at the same time. The GS1582 will assert the XPOINT_ERROR host interface bit if any audio channel is programmed to be included in both groups. 40117 - 1 November 2007 56 of 114 GS1582 Data Sheet The source channel is set via the host interface. Table 4-18 lists the 3-bit address for audio channel mapping. Table 4-18: Audio Channel Mapping Codes Audio Input Channel Group 1 channel 1 Group 1 channel 2 Group 1 channel 3 Group 1 channel 4 Group 2 channel 1 Group 2 channel 2 Group 2 channel 3 Group 2 channel 4 3-bit Host Interface Source Address 000b 001b 010b 011b 100b 101b 110b 111b Table 4-19: Source Input Address Registers Name GP1_CH1_SRC[2:0] GP1_CH2_SRC[2:0] GP1_CH3_SRC[2:0] GP1_CH4_SRC[2:0] GP2_CH1_SRC[2:0] GP2_CH2_SRC[2:0] GP2_CH3_SRC[2:0] GP2_CH4_SRC[2:0] Description Group 1 channel 1 source selector Group 1 channel 2 source selector Group 1 channel 3 source selector Group 1 channel 4 source selector Group 2 channel 1 source selector Group 2 channel 2 source selector Group 2 channel 3 source selector Group 2 channel 4 source selector Default 000b 001b 010b 011b 100b 101b 110b 111b NOTE: Audio channels can be paired only when both channels are derived from the same word clock and are synchronous. 4.7.20 Audio Word Clock The GS1582 uses two word clocks, WCLK_1 and WCLK_2. By default, Audio group 1 will use the clock at the WCLK_1 input, and Audio group 2 will use the word clock at WCLK_2. The word clock assignment for each audio group can be changed by programming the GP1_WCLK_SRC[1:0] and GP2_WCLK_SRC[1:0] registers. In AES mode, the audio clocks are extracted from the input audio data. By default, audio clock for group 1 is extracted from channel pair 1/2, and audio clock group 2 is extracted from channel pair 5/6. The default can be changed by programming 40117 - 1 November 2007 57 of 114 GS1582 Data Sheet the GP1_WCLK_SRC[1:0] and GP2_WCLK_SRC[1:0] register. Table 4-20: Audio Clock Selection Host Interface Settings shows the audio clock source for each setting of the registers. Each audio group consists of 4 channels, which share the same word clock. Therefore, the audio data applied to each channel within the group must be the same format and have identical word clock requirements. NOTE: In AES mode, by default, word clock is extracted from channels 1/2 for Audio group 1 and channels 5/6 for Audio group 2. If audio is applied only to 3/4 or 7/8 only, then no audio is embedded until the word clock source is changed from channels 1/2 or 5/6, to channels 3/4 or 7/8. Table 4-20: Audio Clock Selection Host Interface Settings GP_WCLK_SRC[1:0] 00b 01b 10b 11b Word Clock Extraction Source (AES Mode) Channels 1/2 Channels 3/4 Channels 5/6 Channels 7/8 WCLK Source (Serial Audio Mode) WCLK_1 WCLK_1 WCLK_2 WCLK_2 4.7.21 GS1582 SD Audio FIFO Block The GS1582 SD audio FIFO block contains the audio sample buffers. There is a buffer per audio channel, which are 52 audio samples deep. At power up or reset, the read pointer is held at the zero position until 26 samples have been written into the FIFO. Once audio is being multiplexed, the offset between the audio sample buffer read and write pointers is maintained at an average of 26 samples. The position of the write pointer with respect to the read pointer is checked constantly. If the write pointer is less than 6 samples ahead of the read pointer, a sample is repeated from the read-side of the buffer. If the write pointer is less than 6 samples behind the read pointer, a sample is dropped. This scheme avoids buffer underflow/overflow conditions. The repeat or drop sample operation is performed up to a maximum of 28 consecutive times. After 28 repeat/drops, the GS1582 will mute (null audio packets are embedded). The audio buffer pointer offset can be reduced from 26 samples to 12 or 6 samples using the OS_SEL[1:0] host interface register. The default setting is 26 samples (see Table 4-21). When the OS_SEL[1:0] bits are set for 6-sample pointer offset, no boundary checking is performed. 40117 - 1 November 2007 58 of 114 GS1582 Data Sheet Table 4-21: Audio Buffer Pointer Offset Settings OS_SEL[1:0] 00 01 10 Buffer Pointer Offset 26 samples (default) 12 samples 6 samples The CLEAR_AUDIO bit in the host interface can be used to clear the FIFOs. When asserted, this bit resets the FIFOs to the start-up state. 4.7.22 Audio Sample Distributions 4.7.22.1 525-line Audio Sample Distribution This following sample distribution allows the embedding of 16 channels (4 audio groups) of 24-bit sampled audio into the HANC of 525-line based video formats. The sample distribution is established for group 1 and then offset by 1 line for each subsequent group. The sample distribution is as follows (start line is 12): {[3](10+G),([4],[3]15)15,[4],[3](11-G),[0],[3](3+G),([4],[3]15)15,[4/3],[3]12,[4],[3](4-G),[0]}5 [#] = Number of samples / line [4/3] = One line with either 3 or 4 samples depending on five-frame sequence (#) = Number of times to repeat the sequence. When this # is 0, no samples are inserted G = Audio group number from 1 to 4 {...}5 = 5-frame sequence as shown in Table 4-22: Table 4-22: 5-frame Sequence Sample Distribution Frame 1 2 3 4 5 Number of samples 1602 1601 1602 1601 1602 Table 4-23, Table 4-24, Table 4-25, and Table 4-26 show the audio sample distributions for each of the four audio groups. Each distribution has 525 lines with either 1602 or 1601 samples based on the frame number of the five-frame sequence. 40117 - 1 November 2007 59 of 114 GS1582 Data Sheet NOTE: When 1602 samples are required, the [4/3] term represents a line with 4 samples. When 1601 samples are required, the [4/3] term represents a line with 3 samples. Table 4-23: Group 1 Audio Sample Distribution [3](10+1) Samples Lines 33 11 ([4],[3]15)15 735 240 [4],[3](11-1) 34 11 [0],[3](3+1) 12 5 ([4],[3]15)15 735 240 [4/3],[3]12 40 / 39 13 [4],[3](4-1),[0] 13 5 Table 4-24: Group 2 Audio Sample Distribution [3](10+2) Samples Lines 36 12 ([4],[3]15)15 735 240 [4],[3](11-2) 31 10 [0],[3](3+2) 15 6 ([4],[3]15)15 735 240 [4/3],[3]12 40 / 39 13 [4],[3](4-2),[0] 10 4 Table 4-25: Group 3 Audio Sample Distribution [3](10+3) Samples Lines 39 13 ([4],[3]15)15 735 240 [4],[3](11-3) 28 9 [0],[3](3+3) 18 7 ([4],[3]15)15 735 240 [4/3],[3]12 40 / 39 13 [4],[3](4-3),[0] 7 3 Table 4-26: Group 4 Audio Sample Distribution [3](10+4) Samples Lines 42 14 ([4],[3]15)15 735 240 [4],[3](11-4) 25 8 [0],[3](3+4) 21 8 ([4],[3]15)15 735 240 [4/3],[3]12 40 / 39 13 [4],[3](4-4),[0] 4 2 4.7.22.2 625-line Audio Sample Distribution The following sample distribution is for 625-line video standards which leaves more free HANC space when inserting 16 channels (4 audio groups) of 24-bit sampled audio. The sample distribution is established for group 1 and then offset by 1 line for each subsequent group. The sample distribution is as follows (start line is 8): [3](G-1),([4],[3]11)25,[4],[3](12-G),[0], [3](G-1),([4],[3]11)24,[4],[3](23-G),[0] (#) [#] = Number of samples / line = Number of times to repeat the sequence 40117 - 1 November 2007 60 of 114 GS1582 Data Sheet [3](0) = No lines with no samples G = Audio group number from 1 to 4 NOTE: For audio group 1, the [3](G-1) terms are 0 (zero) and lines 8 and 321 start with the 4 samples of the ([4],[3]11)25 and ([4],[3]11)24 sequences, respectively. Table 4-27, Table 4-28, Table 4-29, and Table 4-30 show the audio sample distributions for each of the four audio groups. Each distribution has 625 lines with 1920 samples. Table 4-27: Group 1 Audio Sample Distribution [3](1-1) Samples Lines 0 0 ([4],[3]11)25 925 300 [4],[3](12-1) 37 12 [0],[3](1-1) 0 1 ([4],[3]11)24 888 288 [4],[3](23-1),[0] 70 24 Table 4-28: Group 2 Audio Sample Distribution [3](2-1) Samples Lines 3 1 ([4],[3]11)25 925 300 [4],[3](12-2) 34 11 [0],[3](2-1) 3 2 ([4],[3]11)24 888 288 [4],[3](23-2),[0] 67 23 Table 4-29: Group 3 Audio Sample Distribution [3](3-1) Samples Lines 6 2 ([4],[3]11)25 925 300 [4],[3](12-3) 31 10 [0],[3](3-1) 6 3 ([4],[3]11)24 888 288 [4],[3](23-3),[0] 64 22 Table 4-30: Group 4 Audio Sample Distribution [3](4-1) Samples Lines 9 3 ([4],[3]11)25 925 300 [4],[3](12-4) 28 9 [0],[3](4-1) 9 4 ([4],[3]11)24 888 288 [4],[3](23-4),[0] 61 21 40117 - 1 November 2007 61 of 114 GS1582 Data Sheet 4.7.22.3 Synchronous Audio Sample Distributions Table 4-31 lists the audio sample distributions for synchronous audio at all the video frame rates supported by the GS1582. Table 4-31: Synchronous Audio Sample Distributions Frame Rate (fps) 30 29.97 25 60 59.94 24 23.98 Samples per Video Frame 1600/1 8008/5 1920/1 800/1 4004/5 2000/1 2002/1 4.7.23 Audio Mute When the AUDIO_MUTEn bits of the host interface are set HIGH, the embedded audio sample data will be set to all zeros (null audio packets). To set all the embedded audio channels to mute, set the host interface AUDIO_ALL bit HIGH. Refer to Section 4.13.3 for GS1582 status and configuration registers. 4.8 Ancillary Data Insertion Horizontal or vertical ancillary data words may be inserted on up to four different lines per video frame. In order to insert HANC data, the ANC_TYPE bit in the host interface, must be set LOW. VANC data can be inserted by setting the ANC_TYPE bit in the host interface HIGH. By default, at power up, HANC data insertion is selected. The user must write the ancillary data words to be inserted, the line number for the insertion, and the total number of words to be inserted to the designated registers in the host interface. At power up, or after system reset, all ANC data insertion line numbers and total number of words default to zero. All data words including the ancillary packet ADF, DBN, DC, DID, SDID, and CHECKSUM (placeholder) must be provided. The user provided CHECKSUM word is a placeholder. The correct value will be calculated and inserted automatically. Two modes of operation are provided - separate line mode and concatenated mode. By default, at power up or after system reset, separate line operating mode is selected. The GS1582 ancillary data insertion provides no error checking or correction. The provided ancillary data must be fully SMPTE compliant. 40117 - 1 November 2007 62 of 114 GS1582 Data Sheet The PACKET_MISSED bit in the host interface is set if: * * * An ancillary data packet is only partially inserted because there is no more free space in the HANC or VANC region of the selected line An ancillary data packet is not inserted at all because there is no free space in the HANC or VANC region of the selected line The number of words to insert programmed through the host interface is greater than the maximum allowed for the operating mode (128 in separate line mode or 512 in concatenated line mode). Under this condition, the bit will be set once the maximum number has been reached This bit is cleared once per frame on the rising edge of V or when it is read through the host interface. In SD mode, two modes of operation are provided - separate line mode and concatenated mode. By default, at power up or after system reset, separate line operating mode is selected. Ancillary data packets are inserted into the multiplexed YCbCr video stream. In HD mode, by default ancillary data packets will be inserted into the luma channel. Insertion in the chroma channel may be selected via the host interface. Ancillary data insertion in the luma and chroma channels can be selected on a per line basis. Ancillary data insertion only takes place if the IOPROC_EN/DIS pin is set HIGH, SMPTE_BYPASS is set HIGH, and the ANC_INS bit in the IOPROC_DISABLE register is set LOW. NOTE 1: It is good practice to program the ancillary data words prior to programming the line number and number of words. Ancillary data insertion only begins once the line number and number of words are set to a non-zero value. Therefore, this practice ensures that no data is written to the ANC space before the programming is complete. As such, no unintended data is written to the ANC space, even if the programmed line number is reached before the programming is complete. Also, read/write conflicts are avoided. NOTE 2: In both separate line mode and concatenated mode, more than one ANC packet may be inserted per line. The user provided ANC packets must contain a checksum place holder word. The correct checksum for each packet will then be re-calculated and inserted by GS1582. The total number of words for all the provided ancillary data packets with checksum should not exceed 128 in separate line mode and 512 in concatenated mode. 4.8.1 Ancillary Data Insertion Operating Mode 4.8.1.1 Separate Line Mode In separate line mode, it is possible to insert horizontal or vertical ancillary data on up to four lines per video frame. For each of the four video lines, up to 128 8-bit HANC or VANC data words can be inserted. Separate line mode is selected by setting the ANC_INS_MODE bit in the host interface LOW. By default, at power up, separate line mode is selected. 40117 - 1 November 2007 63 of 114 GS1582 Data Sheet The non-zero video line numbers on which to insert the ancillary data, the ancillary data type (HANC or VANC), and the total number of words to insert per line must be provided via the host interface. At power up, or after system reset, all ancillary data insertion line numbers and total number of words default to zero. If the total number of data words specified per line exceeds 128 only the first 128 data words will be inserted. The device automatically converts the provided 8-bit data words into the 10-bit data, formatted according to SMPTE 291M prior to insertion. 4.8.1.2 Concatenated Mode In concatenated mode, it is possible to insert up to 512 8-bit horizontal or vertical ancillary data words on one line per video frame. Concatenated line mode can be selected by setting the ANC_INS_MODE bit in the host interface HIGH. By default, at power up, separate line mode is selected. The non-zero video line number on which to insert the ancillary data, the ancillary data type (HANC or VANC), and the total number of words to insert must be provided via the host interface. At power up, or after system reset, the ancillary data insertion line number and total number of words default to zero. If the total number of data words specified exceeds 512 only the first 512 data words will be inserted. The device automatically converts the provided 8-bit data words into the 10-bit data formatted according to SMPTE 291M prior to insertion. 4.8.2 HANC Insertion By default, at power up or after system reset, all ancillary data is inserted in the HANC space. Data is inserted contiguously starting at the TRS EAV or the first available location following any audio and pre-existing ancillary data packets. Data insertion terminates when all provided data words have been inserted or at the start of the TRS SAV code, whichever occurs first. If termination occurs before all words have been inserted, the PACKET_MISSED bit will be set in the host interface. NOTE 1: EDH packet insertion in SD mode occurs following ancillary data insertion. Thus, any HANC data inserted on the same line as the EDH packet may be overwritten during EDH insertion. When HANC data is inserted on an EDH line, the PACKET_MISSED bit may be erroneously set, even though the ancillary data packet has been inserted correctly. NOTE 2: HANC space ancillary data headers undergo 8-bit to 10-bit remapping. This means that when the 8 MSBs are all zero, the value gets mapped to 000 and when the 8 MSBs are all 1, the value gets mapped to 3FF. (i.e. 000, 001, 002, 003 --> 000 and 3FE, 3FD, 3FC --> 3FF) 40117 - 1 November 2007 64 of 114 GS1582 Data Sheet 4.8.3 VANC Insertion Ancillary data insertion into the VANC space can be selected via the host interface. Data is inserted contiguously starting at the TRS SAV or the first available location following any pre-existing ancillary data packets. Data insertion terminates when all provided data words have been inserted or at the start of the TRS EAV code, whichever occurs first. If termination occurs before all words have been inserted, the PACKET_MISSED bit will be set in the host interface. NOTE: When ancillary data is inserted into the active region of the video raster using the VANC feature, if the ILLEGAL_REMAP in the IOPROC_DISABLE register bit is set to 0, then the ADFs are remapped to '004 | 3FB | 3FB' and the downstream devices will not detect the ancillary data packets. 4.9 Additional Processing Functions The GS1582 incorporates additional data processing which is available in SMPTE mode only, see SMPTE Mode on page 28. 4.9.1 ANC Data Blanking The horizontal and vertical ancillary spaces of the input video may be 'blanked' by the GS1582. In this mode, the TRS words and active video will be preserved. Any additional processing functions including audio embedding, including ancillary data insertion, occur after blanking and will be present in the output video stream. This function is enabled by setting the ANC_BLANK pin LOW. 4.9.2 Automatic Video Standard Detection The GS1582 can detect the input video standard by using the timing parameters extracted from the received TRS ID words, the supplied H_Blanking, V_Blanking, and F_Digital timing signals, or the CEA 861 timing signals, see HVF Timing on page 28 and CEA 861 Timing on page 29. This information is presented in the VIDEO_STANDARD register (Table 4-32). Total samples per line, active samples per line, total lines per field/frame and active lines per field/frame are also calculated and available via the RASTER_STRUCTURE registers (Table 4-33). These line and sample count registers are updated once per frame at the end of line 12. After device reset, the four RASTER_STRUCTURE registers default to zero. 40117 - 1 November 2007 65 of 114 GS1582 Data Sheet Table 4-32: Host Interface Description for Video Standard Register Register Name VIDEO_STANDARD Address: 004h Bit 15 14-10 9 Name - VD_STD[4:0] INT_PROG Description Not Used. Video Data Standard (see Table 4-34). Interlace/Progressive: Set LOW if detected video standard is PROGRESSIVE and is set HIGH if it is INTERLACED. Standard Lock: Set HIGH when the device has achieved full synchronization. Not Used. R/W - R R Default - 0 0 8 7-0 STD_LOCK - R - 0 - Table 4-33: Host Interface Description for Raster Structure Registers Register Name RASTER_STRUCTURE1 Address: 00Eh RASTER_STRUCTURE2 Address: 00Fh RASTER_STRUCTURE3 Address: 010h RASTER_STRUCTURE4 Address: 011h Bit 15-12 11-0 15-13 12-0 15-11 10-0 15-11 10-0 - Name Description Not Used. Words Per Active Line Not Used. Words Per Total Line. Not Used. Total Lines Per Frame Not Used. Active Lines Per Field R/W - R - R - R - R Default - 0 - 0 - 0 - 0 RASTER_STRUCTURE_1[11:0] - RASTER_STRUCTURE_2[12:0] - RASTER_STRUCTURE_3[10:0] - RASTER_STRUCTURE_4[10:0] 4.9.3 Video Standard Indication The value reported in the VD_STD[4:0] bits of the VIDEO_STANDARD register corresponds to the SMPTE standards as shown in Table 4-34. In addition to the 5-bit video standard code word, the VIDEO_STANDARD register also contains two status bits. The STD_LOCK bit will be set HIGH whenever the device has achieved full synchronization. The INT_PROG bit will be set LOW if the detected video standard is progressive and HIGH if the detected video standard is interlaced. The VD_STD[4:0], STD_LOCK and INT_PROG bits of the VIDEO_STANDARD register will default to zero after device reset. The VD_STD[4:0] and INT_PROG bits will also default to zero if the SMPTE_BYPASS pin is asserted LOW. The STD_LOCK bit will retain its previous value if the PCLK is removed. 40117 - 1 November 2007 66 of 114 GS1582 Data Sheet Table 4-34: Supported Video Standards VD_STD[4:0] 00h 01h 02h 03h 04h 05h 06h 07h 08h 09h 0Ah 0Bh 0Ch SMPTE Standard 296M (HD) 296M (HD) 296M (HD) 296M (HD) 296M (HD) 296M (HD) 296M (HD) 296M (HD) 296M (HD) 296M (HD) 274M (HD) 274M (HD) 274M (HD) Video Format 1280x720/60 (1:1) 1280x720/60 (1:1) - EM 1280x720/30 (1:1) 1280x720/30 (1:1) - EM 1280x720/50 (1:1) 1280x720/50 (1:1) - EM 1280x720/25 (1:1) 1280x720/25 (1:1) - EM 1280x720/24 (1:1) 1280x720/24 (1:1) - EM 1920x1080/60 (2:1) or 1920x1080/30 (PsF) 1920x1080/30 (1:1) 1920x1080/50 (2:1) or 1920x1080/25 (PsF) Length of HANC 358 198 2008 408 688 240 2668 492 2833 513 268 268 708 Length of Active Video 1280 1440 1280 2880 1280 1728 1280 3456 1280 3600 1920 1920 1920 Total Samples 1650 1650 3300 3300 1980 1980 3960 3960 4125 4125 2200 2200 2640 SMPTE352M Lines 13 13 13 13 13 13 13 13 13 13 10, 572 18 10, 572 0Dh 0Eh 0Fh 10h 11h 12h 13h 14h 15h 16h 274M (HD) 274M (HD) 274M (HD) 274M (HD) 274M (HD) 274M (HD) 274M (HD) 295M (HD) 260M (HD) 125M (SD) 1920x1080/25 (1:1) 1920x1080/25 (1:1) - EM 1920x1080/25 (PsF) - EM 1920x1080/24 (1:1) 1920x1080/24 (PsF) 1920x1080/24 (1:1) - EM 1920x1080/24 (PsF) - EM 1920x1080/50 (2:1) 1920x1035/60 (2:1) 1440x487/60 (2:1) (Or dual link progressive) 708 324 324 818 818 338 338 444 268 268 1920 2304 2304 1920 1920 2400 2400 1920 1920 1440 2640 2640 2640 2750 2750 2750 2750 2376 2200 1716 18 18 10, 572 18 10, 572 18 10, 572 10, 572 10, 572 13, 276 17h 19h 1Bh 18h 125M (SD) 125M (SD) 125M (SD) ITU-R BT.656 (SD) 1440x507/60 (2:1) 525-line 487 generic 525-line 507 generic 1440x576/50 (2:1) (Or dual link progressive) 268 - - 280 1440 - - 1440 1716 1716 1716 1728 13, 276 13, 276 13, 276 9, 322 40117 - 1 November 2007 67 of 114 GS1582 Data Sheet Table 4-34: Supported Video Standards (Continued) VD_STD[4:0] 1Ah SMPTE Standard ITU-R BT.656 (SD) Video Format 625-line generic (EM) Length of HANC - Length of Active Video - Total Samples 1728 SMPTE352M Lines 9, 322 1Dh 1Eh 1Ch, 1Fh Unknown HD Unknown SD Reserved - - - - - - - - - - - - - - - NOTE: Though the GS1582 will work correctly on and serialize both 59.94Hz and 60Hz formats, it will not distinguish between them. 4.9.4 Packet Generation and Insertion The GS1582 can also calculate, assemble and insert TRS ID words, and various types of ancillary data packets. These features are only available when the IOPROC_EN/DIS pin is set HIGH. Individual insertion features may be enabled or disabled via the IOPROC_DISABLE register (Table 4-35). All of the IOPROC_DISABLE register bits default to '0' after device reset, enabling all of the processing features. To disable any individual error correction feature, set the corresponding bit HIGH in this register. 40117 - 1 November 2007 68 of 114 GS1582 Data Sheet Table 4-35: Host Interface Description for Internal Processing Disable Register Register Name IOPROC_DISABLE Address: 000h Bit 15-13 12 Name - TIM_861_PIN_EN Description Not Used. Set to zero. Setting this bit LOW allows the timing mode to be selectable through the CEA_861bit. Setting this bit HIGH allows the timing mode to be selectable through the CEA_861 bit, regardless of the pin setting. Enable or disable ancillary data insertion. Set LOW for enable. Set HIGH for disable. Disable audio embedding. CEA_861 pin override bit. Active when TIM_861_PIN_EN bit is set HIGH. Set CEA_861 bit LOW to enable CEA 861 timing. Set this bit HIGH to disable CEA 861 timing. Horizontal blanking timing configuration. Set LOW when the H/HSYNC input timing is based on active line blanking (default). Set HIGH when the H input timing is based on the H bit of the TRS words. See Figure 4-2. Not Used. Set to zero. SMPTE352M packet insertion. In HD mode, 352M packets are inserted in the luma channel only when one of the bytes in the VIDEO_FORMAT_A or VIDEO_FORMAT_B registers are programmed with non-zero values. Set HIGH to disable. Illegal Code Remapping. Detection and correction of illegal code words within the active picture area (AP). Set HIGH to disable. Error Detection & Handling (EDH) Cyclical Redundancy Check (CRC) error correction. In SD mode the GS1582 will generate and insert EDH packets. Set HIGH to disable. Ancillary Data Checksum insertion. Set HIGH to disable. Luma and chroma line-based CRC insertion. In HD mode, line-based CRC words are inserted in both the luma and chroma channels. Set HIGH to disable Luma and chroma line number insertion - HD mode only. Set HIGH to disable. Timing Reference Signal Insertion. Set HIGH to disable. R/W - R/W Default 0 0 11 10 9 ANC_INS AUDIO_EMBED CEA_861 R/W R/W R/W 0 0 0 8 H_CONFIG R/W 0 7 6 - 352M_INS - R/W 0 0 5 ILLEGAL_REMAP R/W 0 4 EDH_CRC_INS R/W 0 3 2 ANC_CSUM_INS CRC_INS R/W R/W 0 0 1 0 LNUM_INS TRS_INS R/W R/W 0 0 4.9.4.1 SMPTE 352M Payload Identifier Packet Insertion The GS1582 can generate and insert SMPTE 352M payload identifier ancillary data packets. When this feature is enabled, the device will automatically generate the ancillary data preambles, (DID, SDID, DBN, DC), and calculate the checksum. The SMPTE 40117 - 1 November 2007 69 of 114 GS1582 Data Sheet 352M packet will be inserted into the data stream according to the line numbers programmed in the LINE_352M_f1 and LINE_352M_f2 registers (Table 4-36). Packet insertion will only take place if at least one of the bytes in the VIDEO_FORMAT_A or VIDEO_FORMAT_B registers are programmed with a non-zero value (Table 4-37). In addition, the 352M_INS bit must be set LOW (Table 4-35). NOTE: If there are existing 352M packets in the input stream, and ANC_BLANK is set HIGH (disabled), then the existing data is preserved and new 352M is inserted. The GS1582 does not overwrite existing 352M data. The GS1582 will differentiate between PsF and interlaced formats based on bits 14 and 15 of the VIDEO_FORMAT_A register. The packets will be inserted immediately after the EAV word in SD video streams and immediately after the line-based CRC word in the luma channel of HD video streams. If other ancillary packets exist in the horizontal ancillary space 352M packets will be inserted immediatly following these packets. SMPTE 352M packets will not be inserted if there is insufficient room in the HANC space. Table 4-36: Host Interface Description for SMPTE 352M Packet Line Number Insertion Registers Register Name LINE_0_352M Address: 01Bh Bit 15-11 10-0 15-11 10-0 Name - LINE_0_352M[10:0] - LINE_1_352M[10:0] Description Not Used. Line number where SMPTE352M packet is inserted in field 1. Not Used. Line number where SMPTE352M packet is inserted in field 2. R/W - R/W - R/W Default - 0 - 0 LINE_1_352M Address: 01Ch Table 4-37: Host Interface Description for SMPTE 352M Payload Identifier Registers Register Name VIDEO_FORMAT_B Address: 00Bh 7-0 Bit 15-8 Name Video_Format[2] [7:0] Video_Format[1] [7:0] Video_Format[4] [7:0] Video_Format[3] [7:0] Description SMPTE352M Byte 4 information must be programmed in this register when 352M_INS = LOW. SMPTE352M Byte 3information must be programmed in this register when 352M_INS = LOW. SMPTE352M Byte 2information must be programmed in this register when 352M_INS = LOW. SMPTE352M Byte 1information must be programmed in this register when 352M_INS = LOW. R/W R/W Default 0 R/W 0 VIDEO_FORMAT_A Address: 00Ah 15-8 R/W 0 7-0 R/W 0 40117 - 1 November 2007 70 of 114 GS1582 Data Sheet 4.9.4.2 Illegal Code Remapping If the ILLEGAL_REMAP bit of the IOPROC_DISABLE register is set LOW, the GS1582 will remap all codes within the active picture between the values of 3FCh and 3FFh to 3FBh. All codes within the active picture area between the values of 000h and 003h will be remapped to 004h. In addition, 8-bit TRS and ancillary data preambles will be remapped to 10-bit values. 4.9.4.3 EDH Generation and Insertion When operating in SD mode, (SD/HD = HIGH), the GS1582 will generate and insert complete EDH packets. Packet generation and insertion will only take place if the EDH_CRC_INS bit of the IOPROC_DISABLE register is set LOW. The GS1582 will generate all of the required EDH packet data including all ancillary data preambles DID, DBN, DC, reserved code words, and the checksum. Calculation of both full field (FF) and active picture (AP) CRC's will be carried out by the device. SMPTE RP165 specifies the calculation ranges and scope of EDH data for standard 525 and 625 component digital interfaces. The GS1582 uses these standard ranges by default. If the received video format does not correspond to 525 or 625 digital component video standards, then the ranges will be determined from the received TRS ID words or supplied H_Blanking, V_Blanking, and F_Digital timing signals; or HSYNC, VSYNC and DE CEA 861 timing signals. See HVF Timing on page 28, and CEA 861 Timing on page 29. The first active and full field pixel will always be the first pixel after the SAV TRS code word. The last active and full field pixel will always be the last pixel before the start of the EAV TRS code words. EDH error flags (EDH, EDA, IDH, IDA and UES) for ancillary data, full field and active picture will also be inserted when the corresponding bit of the EDH_FLAG register is set HIGH. (Table 4-38). NOTE 1: The EDH flag registers must be updated once per field. The prepared EDH packet will be inserted at the appropriate line according to SMPTE RP165. The start pixel position of the inserted packet will be based on the SAV position of that line such that the last byte of the EDH packet (the checksum) will be placed in the sample immediately preceding the start of the SAV TRS word. NOTE 2: EDH packets will not be inserted if there is insufficient room in the HANC space. 40117 - 1 November 2007 71 of 114 GS1582 Data Sheet Table 4-38: Host Interface Description for EDH Flag Register (SD Mode Only) Register Name EDH_FLAG Address: 002h Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Name - ANC-UES ANC-IDA ANC-IDH ANC-EDA ANC-EDH FF-UES FF-IDA FF-IDH FF-EDA FF-EDH AP-UES AP-IDA AP-IDH AP-EDA AP-EDH Description Not Used. Ancillary Unknown Error Status flag will be generated and inserted. Ancillary Internal device error Detected Already flag will be generated and inserted. Ancillary Internal device error Detected Here flag will be generated and inserted. Ancillary Error Detected Already flag will be generated and inserted. Ancillary Error Detected Here flag will be generated and inserted. Full Field Unknown Error flag will be generated and inserted. Full Field Internal device error Detected Already flag will be generated and inserted. Full Field Internal device error Detected flag will be generated and inserted. Full Field Error Detected Already flag will be generated and inserted. Full Field Error Detected Here flag will be generated and inserted. Active Picture Unknown Error Status flag will be generated and inserted. Active Picture Internal device error Detected Already flag will be generated and inserted. Active Picture Internal device error Detected Here flag will be generated and inserted. Active Picture Error Detected Already flag will be generated and inserted. Active Picture Error Detected Here flag will be generated and inserted. R/W - R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W Default - 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 40117 - 1 November 2007 72 of 114 GS1582 Data Sheet 4.9.4.4 Ancillary Data Checksum Generation and Insertion The GS1582 will calculate checksums for all detected ancillary data packets presented to the device. These calculated checksum values are inserted into the data stream prior to serialization. Ancillary data checksum generation and insertion will only take place if the ANC_CSUM_INS bit of the IOPROC_DISABLE register is set LOW. NOTE: The GS1582 will recalculate the checksum and, if incorrect, will re-insert the correct value. However, the GS1582 does not check the correctness of the parity bit. That is, if all the bits from 0 to 8 in the checksum word are correct and only bit 9 (the parity bit, which is the inverse of bit 8) is incorrect, then the checksum word is not re-calculated. If even one of bit 0 to bit 8 has an incorrect value, then the checksum word is re-calculated and re-inserted. 4.9.4.5 Line Based CRC Generation and Insertion The GS1582 will generate and insert line based CRC words into both the luma and chroma channels of the data stream. This feature is only available in HD mode and is enabled by setting the CRC_INS bit of the IOPROC_DISABLE register LOW. 4.9.4.6 HD Line Number Generation and Insertion In HD mode, the GS1582 will calculate and insert line numbers into the luma and chroma channels of the output data stream. Line number generation is in accordance with the relevant HD video standard as determined by the device, see Automatic Video Standard Detection on page 65. This feature is enabled when SD/HD = LOW, and the LNUM_INS bit of the IOPROC_DISABLE register is set LOW. 4.9.4.7 TRS Generation and Insertion The GS1582 can generate and insert 10-bit TRS code words into the data stream as required. This feature is enabled by setting the TRS_INS bit of the IOPROC_DISABLE register LOW. TRS word generation will be performed in accordance with the timing parameters generated by the device which will be locked either to the received TRS ID words, the supplied H_Blanking, V_Blanking, and F_Digital timing signals, or the CEA 861 timing signals, see HVF Timing on page 28 and CEA 861 Timing on page 29. 4.10 Parallel to Serial Conversion The GS1582 can accept either 10-bit or 20-bit parallel data in both SD and HD modes. The supplied PCLK rate must correspond to the settings of the SD/HD and 20bit/10bit pins as shown in Table 4-39. 40117 - 1 November 2007 73 of 114 GS1582 Data Sheet Table 4-39: Serial Digital Output Rates Supplied PCLK Rate Serial Digital Output Rate Pin Settings SD/HD 74.25 or 74.25/1.001 MHz 148.5 or 148.5/1.001MHz 13.5MHz 27MHz 1.485 or 1.485/1.001Gb/s 1.485 or 1.485/1.001Gb/s 270Mb/s 270Mb/s LOW LOW HIGH HIGH 20bit/10bit HIGH LOW HIGH LOW 4.11 Internal ClockCleanerTM PLL To obtain a clean clock signal for serialization and transmission, an external VCO signal is locked to the input PCLK via the GS1582's integrated phase-locked loop. This high quality analog PLL has a bang-bang implementation, which automatically narrows the loop bandwidth in the presence of jitter, allowing the GS1582 to significantly attenuate jitter on the incoming PCLK. 4.11.1 External VCO The GS1582 requires the GO1555 external voltage controlled oscillator as part of its internal PLL. Power for the external VCO is generated by the GS1582 from an integrated voltage regulator. The internal regulator uses +3.3V supplied on the CP_VDD / CP_GND pins to provide +2.5V on the VCO_VCC / VCO_GND pins. The external VCO produces a 1.485GHz signal for the PLL, input on the VCO pin of the device. See Typical Application Circuit (Part A) on page 108. NOTE: The VCO_VCC output voltage is guaranteed to be 2.5V only when supplying power to the GO1555. The VCO_VCC pin should not be shorted to GND under any circumstances. 4.11.2 Loop Filter The GS1582 PLL loop filter is an external first order filter formed by a series RC connection as shown in the Typical Application Circuit (Part A) on page 108. The loop filter resistor value sets the bandwidth of the PLL and the capacitor value controls its stability and lock time. A loop filter resistor value between 1 to 20 and a loop filter capacitor value between 1F to 33F are recommended. The GS1582 uses a non-linear, bang-bang, PLL, therefore its bandwidth scales with the input jitter amplitude - greater input jitter results in a smaller loop bandwidth causing more of the input jitter to be rejected. For a given input jitter amplitude, a smaller loop filter resistor produces a narrower loop bandwidth. With an input jitter amplitude of 300ps, for example, the PLL bandwidth can be adjusted from 2KHz to 40117 - 1 November 2007 74 of 114 GS1582 Data Sheet 40KHz by varying the loop filter resistor, as shown in Table 4-40: Loop Filter Component Values. For use with the GEN-ClocksTM timing generators, a narrow loop bandwidth is recommended. Increasing the loop filter capacitor value increases the stability of the PLL, but results in a longer lock time. For loop filter resistors smaller than 7, a capacitor value of 33F is recommended, while larger resistor values can accommodate smaller capacitors. Sample combinations of the loop filter resistor and capacitor values are shown in Table 4-40: Loop Filter Component Values, along with the resulting loop bandwidth. Additional loop bandwidths can be achieved by using different loop filter resistor values. Table 4-40: Loop Filter Component Values Loop Filter Resistor Value 1 Typical Loop Bandwidth* Recommended Loop Filter Capacitor Value 33F Comments 2kHz Narrow bandwidth - provides maximum jitter reduction. Long lock-time. 7 20 8kHz 40kHz 10F 1F Wide bandwidth. Fast lock-time. * Measured with 300ps pk-pk input jitter on PCLK 4.11.3 Lock Detect Output The LOCKED output will be asserted HIGH when the internal PLL has locked to the input PCLK signal. In the absence of the PCLK, when frequency lock has not been achieved, and during device reset, the LOCKED output will be LOW. Lock time, the time it takes for the internal PLL to frequency-lock to the reference PCLK following power-up or standby, is determined by the loop filter capacitor value chosen. A 1F loop filter capacitor, for example, will result in lock times of less than 500s. A 33F loop filter capacitor, on the other hand, will result in a lock time of greater than 5s. NOTE 1: When the PLL is in the process of locking to the reference PCLK, the LOCKED pin may generate LOW and HIGH pulses. The durations of these pulses are dependent on the loop filter capacitor value, but do not exceed 30ms. Once the PLL has achieved frequency lock, the LOCKED pin will remain HIGH and not change state. NOTE 2: When the GS1582 is placed in standby mode, the value of LOCKED is maintained although the PLL does lose lock to the reference PCLK. When STANDBY is released, the PLL will re-lock. During this time, if the LOCKED pin was previously HIGH, it will de-assert approximately 6s later, and re-assert once the PLL has re-locked to the input PCLK. 40117 - 1 November 2007 75 of 114 GS1582 Data Sheet 4.12 Serial Digital Output The GS1582 includes a SMPTE compliant current mode differential serial digital cable driver with automatic slew rate control. The serial output has improved eye quality, exceptional ORL performance, and reduced duty cycle distortion. The cable driver uses a separate +3.3V DC power supply provided via the CD_VDD and CD_GND pins. To enable the output, SDO_EN/DIS must be set HIGH. Setting the SDO_EN/DIS signal LOW will set the SDO and SDO output pins to high impedance, resulting in reduced device power consumption. 4.12.1 Output Swing Nominally, the voltage swing of the serial digital output is 800mVp-p single-ended into a 75 load. This is set externally by connecting the RSET pin to CD_VDD through 750 1% resistor. 4.13 GSPI Host Interface The GS1582 host interface, also called the Gennum Serial Peripheral Interface (GSPI), provides access to configuration/status registers for the video processing and SD and HD audio processing functions of the chip. By default, the device will be "live at power up" with all major functional blocks active in the defined default operating conditions described below. Dedicated configuration pins are provided for basic configuration of the device. The host interface is provided to allow optional configuration of some of the more advanced functions and operating modes of the device. To simplify host interface access to the configuration and status registers, a single contiguous register map is provided for the video and audio functions. Registers are grouped by like function and wherever possible functional configuration will not be spread across multiple registers. The GSPI is comprised of a serial data input signal (SDIN), serial data output signal (SDOUT), an active low chip select (CS), and a burst clock (SCLK). The burst clock must have a duty cycle between 40% and 60% while active. Because these pins are shared with the JTAG interface port, an additional control signal pin JTAG/HOST is provided. When JTAG/HOST is LOW, the GSPI interface is enabled. When operating in GSPI mode, the SCLK, SDIN, and CS are inputs to the device. The SDOUT loops the SDIN back out when GSPI is in write mode, or when CS is HIGH, allowing multiple devices to be connected in series. During reset, SDOUT is held in high-impedance mode. The interface is illustrated in the Figure 4-26. 40117 - 1 November 2007 76 of 114 GS1582 Data Sheet Each GSPI access begins with a 16-bit command word on SDIN indicating the address of the register of interest. This is followed by a 16-bit data word on SDIN in write mode, or a 16-bit data word on SDOUT in read mode. NOTE 1: When operating in SD mode, SD/HD is set HIGH, only the SD video and audio registers are accessible for read or write. Similarly, when operating in HD mode, SD/HD is set LOW, only the HD video and audio registers are accessible for read or write. NOTE 2: When the device is in standby mode (STANDBY = HIGH) no host interface register can be read back or written to. Attempting a read or write will not damage the device. However, all reads will return a value of 0, and no writes will take effect. NOTE 3: In the Configuration and Status Registers, there are several registers that have been designated as Reserved. If possible, writing to these registers should be avoided. If writing a value to these registers is not avoidable, then only a value of 0 should be written to these registers. Writing a value of 1 may alter the functional behaviour of GS1582 but will not permanently damage the device. Application Host GS1582 SCLK CS1 SDOUT SCLK CS SDIN SDOUT GS1582 SCLK CS2 CS SDIN SDIN SDOUT Figure 4-26: Gennum Serial Peripheral Interface (GSPI) 40117 - 1 November 2007 77 of 114 GS1582 Data Sheet 4.13.1 Command Word Description The command word consists of a 16-bit word transmitted MSB first and contains a read/write bit, an Auto-Increment bit and a 12-bit address. Figure 4-27 shows the command word format and bit configurations. Command words are clocked into the GS1582 on the rising edge of the serial clock SCLK, which operates in a burst fashion. When the Auto-Increment bit is set LOW, each command word must be followed by only one data word to ensure proper operation. If the Auto-Increment bit is set HIGH, the following data word will be written into the address specified in the command word, and subsequent data words will be written into incremental addresses from the previous data word. This facilitates multiple address writes without sending a command word for each data word. NOTE: All registers can be written to through single address access or through the auto-increment feature. However, the LSB of the video registers cannot be read through single address read-back. Single address read-back will return a 0 value for the LSB. If auto-increment is used to read back the values from at least two registers, the LSB value read will always be correct. Therefore, for register read-back, it is recommended that auto-increment be used and that at least two registers be read back at a time. MSB R/W RSV LSB RSV AutoInc A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 RSV = Reserved. Must be set to zero. R/W: Read command when R/W = 1 Write command when R/W = 0 Figure 4-27: Command Word MSB D15 LSB D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 Figure 4-28: Data Word 4.13.2 Data Read and Write Timing Read and write mode timing for the GSPI interface is shown in Figure 4-29 and Figure 4-30 respectively. The timing parameters are defined in Table 4-41. When several devices are connected to the GSPI chain, only one CS must be set LOW during a read sequence. During the write sequence, all command and subsequent data words are looped through from SDIN to SDOUT. When several devices are connected to the GSPI chain, data can be written simultaneously to all the devices that have CS set LOW. 40117 - 1 November 2007 78 of 114 GS1582 Data Sheet Table 4-41: GSPI Timing Parameters Parameter t0 t1 t2 t3 t4 Definition The minimum duration of time chip select, CS, must be LOW before the first SCLK rising edge. The minimum SCLK period. Duty cycle tolerated by SCLK. Minimum input setup time. Write Cycle: the minimum duration of time between the last SCLK command (or data word if the Auto-Increment bit is HIGH) and the first SCLK of the data word. Read Cycle: the minimum duration of time between the last SCLK command (or data word if the Auto-Increment bit is HIGH) and the first SCLK of the data word. Minimum output hold time. The minimum duration of time between the last SCLK of the GSPI transaction and when CS can be set HIGH. Minimum input hold time. Specification 1.5 ns 100 ns 40% to 60% 1.5 ns 37.1 ns t5 148.4 ns t6 t7 t8 1.5 ns 37.1 ns 1.5 ns t5 SCLK CS t6 R/W RSV RSV AutoInc A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 SDIN SDOUT R/W RSV RSV AutoInc A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 Figure 4-29: GSPI Read Mode Timing t0 SCLK t1 t4 t7 CS t3 R/W RSV RSV AutoInc A11 A10 t2 A9 A8 A7 t8 A6 A5 A4 A3 A2 A1 A0 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 SDIN SDOUT R/W RSV RSV AutoInc A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 Figure 4-30: GSPI Write Mode Timing 40117 - 1 November 2007 79 of 114 GS1582 Data Sheet 4.13.3 Configuration and Status Registers Table 4-42 summarizes the GS1582's internal status and configuration registers. Table 4-43 summarizes the video status and configuration registers. Table 4-44 and Table 4-45 summarizes the SD and HD audio status and configuration registers. All bits are available to the host via the GSPI. Table 4-42: GS1582 Internal Registers Address 000h 002h 004h 005h - 009h 00Ah - 00Bh 00Eh - 011h 01Ah 01Bh - 01Ch Register Name IOPROC_DISABLE EDH_FLAG VIDEO_STANDARD ANC_DATA_TYPE VIDEO_FORMAT RASTER_STRUCTURE GLOBAL_ERROR_MASK_VECTOR LINE_352M See Section Section 4.9.4 Section 4.9.4.3 Section 4.9.2 Section 4.9.4.1 Section 4.9.2 Section 4.9.4.1 40117 - 1 November 2007 80 of 114 GS1582 Data Sheet 4.13.3.1 Video Registers Table 4-43: Video Configuration and Status Registers Address 000h Register Name Reserved TIM_861_PIN_EN Bit 15-13 12 Description Reserved. Selects pin for control for 861 timing converter. Reference: Section 4.3.2 on page 29. R/W R R/W Default 000b 0 ANC_INS 11 Disable for ancillary data insertion feature. Reference: Section 4.8 on page 62. R/W 0 AUDIO_EMBED 10 Disable audio embedding. Reference: Section 4.7 on page 36. R/W 0 CEA_861 9 Disable 861 timing converter. Reference: Section 4.3.2 on page 29. R/W 0 H_CONFIG 8 Horizontal sync timing input configuration. Set LOW when the H input timing is based on active line blanking (default). Set HIGH when the H input timing is based on the H bit of the TRS words. Reference: Section 4.3.1 on page 28. R/W 0 Reserved 352M_INS 7 6 Reserved. SMPTE352M packet insertion. In HD mode, 352M packets are inserted in the luma channel only when one of the bytes in the VIDEO_FORMAT_A or VIDEO_FORMAT_B registers are programmed with non-zero values. Set HIGH to disable. Reference: Section 4.9.4.1 on page 69. R R/W 0 0 ILLEGAL_REMAP 5 Illegal Code Remapping. Detection and correction of illegal code words within the active picture area (AP). Set HIGH to disable. Reference: Section 4.9.4.2 on page 71. R/W 0 EDH_CRC_INS 4 Error Detection & Handling (EDH) Cyclical Redundancy Check (CRC) error correction. In SD mode the GS1582 will generate and insert EDH packets. Set HIGH to disable. Reference: Section 4.9.4.3 on page 71. R/W 0 ANC_CSUM_INS 3 Ancillary Data Checksum insertion. Set HIGH to disable. Reference: Section 4.9.4.4 on page 73. R/W 0 CRC_INS 2 Luma and chroma line-based CRC insertion. In HD mode, line-based CRC words are inserted in both the luma and chroma channels. Set HIGH to disable Reference: Section 4.9.4.5 on page 73. R/W 0 LNUM_INS 1 Luma and chroma line number insertion - HD mode only. Set HIGH to disable. Reference: Section 4.9.4.6 on page 73. R/W 0 TRS_INS 0 Timing Reference Signal Insertion. Set HIGH to disable. Reference: Section 4.9.4.7 on page 73. R/W 0 40117 - 1 November 2007 81 of 114 GS1582 Data Sheet Table 4-43: Video Configuration and Status Registers (Continued) Address 001h 002h Register Name Reserved Reserved ANC-UES Bit 15-0 15 14 Description Reserved. Reserved. Ancillary Unknown Error Status flag will be generated and inserted. SD mode only. Reference: Section 4.9.4.3 on page 71. R/W R R/W R/W Default N/A 0 0 ANC-IDA 13 Ancillary Internal device error Detected Already flag will be generated and inserted. SD mode only. Reference: Section 4.9.4.3 on page 71. R/W ANC-IDH 12 Ancillary Internal device error Detected Here flag will be generated and inserted. SD mode only. Reference: Section 4.9.4.3 on page 71. R/W 0 ANC-EDA 11 Ancillary Error Detected Already flag will be generated and inserted. SD mode only. Reference: Section 4.9.4.3 on page 71. R/W 0 ANC-EDH 10 Ancillary Error Detected Here flag will be generated and inserted. SD mode only. Reference: Section 4.9.4.3 on page 71. R/W 0 FF-UES 9 Full Field Unknown Error flag will be generated and inserted. SD mode only. Reference: Section 4.9.4.3 on page 71. R/W 0 FF-IDA 8 Full Field Internal device error Detected Already flag will be generated and inserted. SD mode only. Reference: Section 4.9.4.3 on page 71. R/W 0 FF-IDH 7 Full Field Internal device error Detected flag will be generated and inserted. SD mode only. Reference: Section 4.9.4.3 on page 71. R/W 0 FF-EDA 6 Full Field Error Detected Already flag will be generated and inserted. SD mode only. Reference: Section 4.9.4.3 on page 71. R/W 0 FF-EDH 5 Full Field Error Detected Here flag will be generated and inserted. SD mode only. Reference: Section 4.9.4.3 on page 71. R/W 0 AP-UES AP-IDA AP-IDH AP-EDA AP-EDH 003h Reserved 4 3 2 1 0 15-0 Active Picture Unknown Error Status flag will be generated and inserted. SD mode only. Active Picture Internal device error Detected Already flag will be generated and inserted. SD mode only. Active Picture Internal device error Detected Here flag will be generated and inserted. SD mode only. Active Picture Error Detected Already flag will be generated and inserted. SD mode only. Active Picture Error Detected Here flag will be generated and inserted. SD mode only. Reserved. R/W R/W R/W R/W R/W R 0 0 0 0 0 N/A 40117 - 1 November 2007 82 of 114 GS1582 Data Sheet Table 4-43: Video Configuration and Status Registers (Continued) Address 004h Register Name Reserved VID_STD[4:0] Bit 15 14-10 Description Reserved Reports the detected video standard. Reference: Section 4.9.3 on page 66. R/W R R Default 0 00000b INT_PROG 9 Interlace/Progressive: Set LOW if detected video standard is PROGRESSIVE and is set HIGH if it is INTERLACED. Reference: Section 4.9.3 on page 66. R 0 STD_LOCK 8 Standard Lock: Set HIGH when the device has achieved full synchronization. Reference: Section 4.9.3 on page 66. R 0 Reserved 005h-009h 00Ah Reserved Video_Format_A[15:8] 7-0 15-0 15-8 Reserved. Reserved. SMPTE 352M Byte 2 information must be programmed in this register when 352M_INS = LOW. Reference: Section 4.9.4.1 on page 69. R R R/W N/A N/A 0 Video_Format_A[7:0] 7-0 SMPTE 352M Byte 1 information must be programmed in this register when 352M_INS = LOW. Reference: Section 4.9.4.1 on page 69. R/W 0 00Bh Video_Format_B[15:8] 15-8 SMPTE 352M Byte 4 information must be programmed in this register when 352M_INS = LOW. Reference: Section 4.9.4.1 on page 69. R/W 0 Video_Format_B[7:0] 7-0 SMPTE 352M Byte 3 information must be programmed in this register when 352M_INS = LOW. Reference: Section 4.9.4.1 on page 69. R/W 0 00Ch-00Dh 00Eh Reserved Reserved RASTER_STRUCTURE_1 15-0 15-12 11-0 Reserved. Reserved. Words Per Active Line Reference: Section 4.9.2 on page 65. R - R N/A - 0 00Fh Reserved RASTER_STRUCTURE_2 15-13 12-0 Reserved. Words Per Total Line. Reference: Section 4.9.2 on page 65. - R - 0 010h Reserved RASTER_STRUCTURE_3 15-11 10-0 Reserved. Total Lines Per Frame Reference: Section 4.9.2 on page 65. - R - 0 011h Reserved RASTER_STRUCTURE_4 15-11 10-0 Reserved. Active Lines Per Field Reference: Section 4.9.2 on page 65. - R - 0 40117 - 1 November 2007 83 of 114 GS1582 Data Sheet Table 4-43: Video Configuration and Status Registers (Continued) Address 012h Register Name Reserved AP_LINE_START_F0[9:0] Bit 15-10 9-0 15-10 9-0 15-10 9-0 15-10 9-0 15-10 9-0 15-10 9-0 15-10 9-0 15-10 9-0 15-0 15-11 10-0 Description Not Used. Set to zero. Field 0 Active Picture start line data used to set EDH calculation range outside of RP 165 values. Reserved. Field 0 Active Picture end line data used to set EDH calculation range outside of RP 165 values. Reserved. Field 1 Active Picture start line data used to set EDH calculation range outside of RP 165 values. Reserved. Field 1 Active Picture end line data used to set EDH calculation range outside of RP 165 values. Reserved. Field 0 Full Field start line data used to set EDH calculation range outside of RP 165 values. Reserved. Field 0 Full Field end line data used to set EDH calculation range outside of RP 165 values. Reserved. Field 1 Full Field start line data used to set EDH calculation range outside of RP-165 values. Reserved. Field 1 Full Field end line data used to set EDH calculation range outside of RP-165 values. Reserved. Reserved. Line number where SMPTE352M packet is inserted in field 1. Reference: Section 4.9.4.1 on page 69. R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W R - R/W Default 0 0 - 0 - 0 - 0 - 0 - 0 - 0 - 0 N/A - 0 013h Reserved AP_LINE_END_F0[9:0] 014h Reserved AP_LINE_START_F1[9:0] 015h Reserved AP_LINE_END_F1[9:0] 016h Reserved FF_LINE_START_F0[9:0] 017h Reserved FF_LINE_END_F0[9:0] 018h Reserved FF_LINE_START_F1[9:0] 019h Reserved FF_LINE_END_F1[9:0] 01Ah 01Bh Reserved Reserved LINE_0_352M[10:0] 01Ch Reserved LINE_1_352M[10:0] 15-11 10-0 Reserved. Line number where SMPTE352M packet is inserted in field 2. Reference: Section 4.9.4.1 on page 69. - R/W - 0 01Dh-01Eh Reserved 15-0 Reserved. R N/A 40117 - 1 November 2007 84 of 114 GS1582 Data Sheet Table 4-43: Video Configuration and Status Registers (Continued) Address 01Fh Register Name FORMAT_ERR Reserved LINE_OFFSET PIXEL_OFFSET Reserved FSYNC_INVERT Bit 15 14-9 8-6 5-3 2-1 0 15 Description 861 timing format error flag. Reserved. Shifts the timing of the output 861 timing signal by up to +/-3 lines. Shifts the timing of the output 861 timing signal by up to +/-3 pixels. Reserved. Inverts the polarity of the detected field. Selects the ANC data insertion operating mode. 0 Separate line mode 1 Concatenated mode Reference: Section 4.8.1 on page 63. R/W R R R/W R/W R R/W R/W Default 0 0 0 0 0 0 0 020h ANC_INS_MODE PACKET_MISSED 14 Flag to indicate ancillary data packet could not be inserted in its entirety. Reference: Section 4.8 on page 62. R 0 RW_CONFLICT Reserved FIRST_LINE_NUMBER 021h ANC_TYPE 13 12-11 10-0 15 Flag to indicate the same RAM address was read and written at the same time. Reserved Defines the line number for the first line in separate line mode or the single line for concatenated mode. Selects the ANC data type as HANC or VANC. 0 HANC 1 VANC Reference: Section 4.8.2 & Section 4.8.3 R R/W R/W R/W 0 0000b 0 0 STREAM_TYPE 14 Selects the luma or chroma stream for ANC insertion. 0 Luma stream 1 Chroma stream This field is ignored in SD mode. Reference: Section 4.8.2 & Section 4.8.3 R/W 0 Reserved FIRST_LINE_NUMBER_OF _WORDS 022h Reserved SECOND_LINE_NUMBER 13-10 9-0 Reserved Defines the total number of data words to insert on the first line in separate line mode or single line in the concatenated mode. Reserved Defines the line number for ANC data insertion for the 2nd line in separate line mode. R/W R/W 0000b 0 15-11 10-0 R/W R/W 00000b 0 40117 - 1 November 2007 85 of 114 GS1582 Data Sheet Table 4-43: Video Configuration and Status Registers (Continued) Address 023h Register Name ANC_TYPE Bit 15 Description Selects the ANC data type as HANC or VANC. 0 HANC 1 VANC Reference: Section 4.8.2 & Section 4.8.3 R/W R/W Default 0 STREAM_TYPE 14 Selects the luma or chroma stream for ANC insertion. 0 Luma stream 1 Chroma stream This field is ignored in SD mode. Reference: Section 4.8.2 & Section 4.8.3 R/W 0 Reserved SECOND_LINE_NUMBER_ OF_WORDS 024h Reserved THIRD_LINE_NUMBER 025h ANC_TYPE 13-10 9-0 15-11 10-0 15 Reserved Defines the total number of data words to insert on the 2nd line in separate line mode. Reserved Defines the line number for ANC data insertion for the 3rd line in separate line mode. Selects the ANC data type as HANC or VANC. 0 HANC 1 VANC Reference: Section 4.8.2 & Section 4.8.3 R/W R/W R/W R/W R/W 0000b 0 00000b 0 0 STREAM_TYPE 14 Selects the luma or chroma stream for ANC insertion. 0 Luma stream 1 Chroma stream This field is ignored in SD mode. Reference: Section 4.8.2 & Section 4.8.3 R/W 0 Reserved THIRD_LINE_NUMBER_OF _WORDS 026 Reserved FOURTH_LINE_NUMBER 027h ANC_TYPE 13-10 9-0 15-11 10-0 15 Reserved. Defines the total number of data words to insert on the 3rd line in separate line mode. Reserved Defines the line number for ANC data insertion for the 4th line in separate line mode. Selects the ANC data type as HANC or VANC. 0 HANC 1 VANC Reference: Section 4.8.2 & Section 4.8.3 R/W R/W R/W R/W R/W 0000b 0 00000b 0 0 STREAM_TYPE 14 Selects the luma or chroma stream for ANC insertion. 0 Luma stream 1 Chroma stream This field is ignored in SD mode. Reference: Section 4.8.2 & Section 4.8.3 R/W 0 Reserved FOURTH_LINE_NUMBER_ OF_WORDS 13-10 9-0 Reserved Defines the total number of data words to insert on the 4th line in separate line mode. R/W R/W 0000b 0 40117 - 1 November 2007 86 of 114 GS1582 Data Sheet Table 4-43: Video Configuration and Status Registers (Continued) Address 040h-07Fh Register Name ANC_DATA_BANK1 Bit 15-0 Description First bank of user defined 8 bit words. 15-8: High order byte 7-0: Low order byte Second bank of user defined 8 bit words. 15-8: High order byte 7-0: Low order byte Third bank of user defined 8 bit words. 15-8: High order byte 7-0: Low order byte Fourth bank of user defined 8 bit words. 15-8: High order byte 7-0: Low order byte R/W W Default 0 080h-0BFh ANC_DATA_BANK2 15-0 W 0 0C0h-0FFh ANC_DATA_BANK3 15-0 W 0 100h-13Fh ANC_DATA_BANK4 15-0 W 0 40117 - 1 November 2007 87 of 114 GS1582 Data Sheet 4.13.3.2 SD Audio Registers Table 4-44: SD Audio Configuration and Status Registers Address 400h Register Name CTR_AGR Bit 15 Description Selects replacement of audio control packets. 0: Do not replace audio control packets. 1: Replace all audio control packets. Reference: Section 4.7.11 on page 48. R/W R/W Default 0 AGR 14 Selects Audio Group Replacement operating mode. Reference: Section 4.7.11 on page 48. R/W 0 ONE_AGR 13 Specifies the replacement of just the group 1 audio. 0: Do not replace only Group 1. 1: Replace only Group 1. Reference: Section 4.7.11 on page 48. R/W 0 CTRB_ON 12 Specifies the embedding of group 2 audio control packets. Reference: Section 4.7.9 on page 45. R/W 1 CLEAR_AUDIO 11 Clears all audio FIFO buffers and puts them in start-up state Reference: Section 4.7.21 on page 58. R/W 0 AFNB_AUTO 10 Group 2 audio frame number generation. Reference: Section 4.7.9 on page 45. R/W 1 CTRA_ON 9 Specifies the embedding of group 1 audio control packets. Reference: Section 4.7.9 on page 45. R/W 1 24BIT 8 Specifies the sample size for embedded audio. Reference: Section 4.7.10 on page 47. R/W 0 AFNA_AUTO 7 Enables group 1 audio frame number generation. Reference: Section 4.7.9 on page 45. R/W 1 AFN_OFS[2:0] 6-4 Offset to add to generated Audio Frame Number. Must be in the range of 0 to 4. The resulting audio frame number will wrap around so as to always be in the 1-5 range. Reference: Section 4.7.16 on page 51. R/W 000b IDB[1:0] 3-2 Specifies the group 2 audio to embed. NOTE: Should IDA and IDB be set to the same value, they automatically revert to their default values. Reference: Section 4.7.10 on page 47. R/W 01b (normal mode) 11b (cascade mode) IDA[1:0] 1-0 Specifies the group 1 audio to embed. NOTE: Should IDA and IDB be set to the same value, they automatically revert to their default values. Reference: Section 4.7.10 on page 47. R/W 00b (normal mode) 10b (cascade mode) 40117 - 1 November 2007 88 of 114 GS1582 Data Sheet Table 4-44: SD Audio Configuration and Status Registers (Continued) Address 401h Register Name Reserved AES_ERRD Bit 15-11 10 Description Reserved Stereo Pair D audio input parity error when using AES format. Automatically cleared when read. Reference: Section 4.7.17.1 on page 53. R/W R R Default 00000b 0 AES_ERRC 9 Stereo Pair C audio input parity error when using AES format. Automatically cleared when read. Reference: Section 4.7.17.1 on page 53. R 0 AES_ERRB 8 Stereo Pair B audio input parity error when using AES format. Automatically cleared when read. Reference: Section 4.7.17.1 on page 53. R 0 AES_ERRA 7 Stereo Pair A audio input parity error when using AES format. Automatically cleared when read. Reference: Section 4.7.17.1 on page 53. R 0 Reserved OFFSET_DISABLE 6-3 2 Reserved Set to disable staggering of group 2 audio sample distribution by one line. Reference: Section 4.7.20 on page 57. R R/W 0 0 OS_SEL[1:0] 1-0 Specifies the audio FIFO buffer size. 00: 52 samples deep, 26 sample start-up count 01: 24 samples deep, 12 sample start-up count 10: 12 samples deep, 6 sample start-up count 11: Reserved. Reference: Section 4.7.21 on page 58. R/W 00b 40117 - 1 November 2007 89 of 114 GS1582 Data Sheet Table 4-44: SD Audio Configuration and Status Registers (Continued) Address 402h Register Name Reserved AXPG4_DET Bit 15 14 Description Reserved. Set while Group 4 audio extended packets are detected. Reference: Section 4.7.2 on page 37. R/W R R Default 0 0 AXPG3_DET 13 Set while Group 3 audio extended packets are detected. Reference: Section 4.7.2 on page 37. R 0 AXPG2_DET 12 Set while Group 2 audio extended packets are detected. Reference: Section 4.7.2 on page 37. R 0 AXPG1_DET 11 Set while Group 1 audio extended packets are detected. Reference: Section 4.7.2 on page 37. R 0 ACPG4_DET 10 Set while Group 4 audio control packets are detected. Reference: Section 4.7.2 on page 37. R 0 ACPG3_DET 9 Set while Group 3 audio control packets are detected. Reference: Section 4.7.2 on page 37. R 0 ACPG2_DET 8 Set while Group 2 audio control packets are detected. Reference: Section 4.7.2 on page 37. R 0 ACPG1_DET 7 Set while Group 1 audio control packets are detected. Reference: Section 4.7.2 on page 37. R 0 ADPG4_DET 6 Set while Group 4 audio data packets are detected. Reference: Section 4.7.2 on page 37. R 0 ADPG3_DET 5 Set while Group 3 audio data packets are detected. Reference: Section 4.7.2 on page 37. R 0 ADPG2_DET 4 Set while Group 2 audio data packets are detected. Reference: Section 4.7.2 on page 37. R 0 ADPG1_DET 3 Set while Group 1 audio data packets are detected. Reference: Section 4.7.2 on page 37. R 0 ACS_APPLY_WAITB 2 Set while the multiplexer is waiting for a status boundary in the Group B group before applying the ACSR[183:0] data to that group. Reference: Section 4.7.18 on page 55. R 0 ACS_APPLY / ACS_APPLY_WAITA 1 ACS_APPLY: Cause channel satus data in ACSR[183:0] to be transferred to the channel status replacement mechanism. The transfer shall not occur until the next status boundary. ACS_APPLY_WAITA: Set while the multiplexer is waiting for a status boundary in Group 1 before applying the ACSR[183:0] data. Reference: Section 4.7.18 on page 55. R/W 0 ACS_REGEN 0 Specifies that Audio Channel Status of all channels should be replaced with ACSR[183:0] field. 0: Do not replace Channel Status 1: Replace Channel Status of all channels Reference: Section 4.7.18 on page 55. 40117 - 1 November 2007 R/W 0 90 of 114 GS1582 Data Sheet Table 4-44: SD Audio Configuration and Status Registers (Continued) Address 403h Register Name Reserved EN_CASCADE Reserved Bit 15-10 9 8-0 15-0 15-14 Description Reserved. Cascade. Reserved. Reserved. Audio input format selector for Stereo Pair D input channels 7 and 8. Reference: Section 4.7.17 on page 52. R/W R R/W R R R/W Default N/A N/A N/A 11b 404h-407h 408h Reserved AMD[1:0] AMC[1:0] 13-12 Audio input format selector for Stereo Pair C input channels 5 and 6. Reference: Section 4.7.17 on page 52. R/W 11b AMB[1:0] 11-10 Audio input format selector for Stereo Pair B input channels 3 and 4. Reference: Section 4.7.17 on page 52. R/W 11b AMA[1:0] 9-8 Audio input format selector for Stereo Pair A input channels 1 and 2. Reference: Section 4.7.4 on page 39. R/W 11b MUTE8 7 Audio input channel 8 mute enable. Reference: Section 4.7.23 on page 62. R/W 0 MUTE7 6 Audio input channel 7 mute enable. Reference: Section 4.7.23 on page 62. R/W 0 MUTE6 5 Audio input channel 6 mute enable. Reference: Section 4.7.23 on page 62. R/W 0 MUTE5 4 Audio input channel 5 mute enable. Reference: Section 4.7.23 on page 62. R/W 0 MUTE4 3 Audio input channel 4 mute enable. Reference: Section 4.7.23 on page 62. R/W 0 MUTE3 2 Audio input channel 3 mute enable. Reference: Section 4.7.23 on page 62. R/W 0 MUTE2 1 Audio input channel 2 mute enable. Reference: Section 4.7.23 on page 62. R/W 0 MUTE1 0 Audio input channel 1 mute enable. Reference: Section 4.7.23 on page 62. R/W 0 40117 - 1 November 2007 91 of 114 GS1582 Data Sheet Table 4-44: SD Audio Configuration and Status Registers (Continued) Address 409h Register Name Reserved GP1_WCLK_SRC[2:0] Bit 15, 12 14-13 Description Reserved Audio group 1 word clock source selector. Reference: Section 4.7.20 on page 57. R/W R/W R/W Default 0 0 GP1_CH4_SRC[2:0] 11-9 Audio group 1 channel 4 source selector. Reference: Section 4.7.19 on page 56. R/W 011b GP1_CH3_SRC[2:0] 8-6 Audio group 1 channel 3 source selector. Reference: Section 4.7.19 on page 56. R/W 010b GP1_CH2_SRC[2:0] 5-3 Audio group 1 channel 2 source selector. Reference: Section 4.7.19 on page 56. R/W 001b GP1_CH1_SRC[2:0] 2-0 Audio group 1 channel 1 source selector. Reference: Section 4.7.19 on page 56. R/W 000b 40Ah Reserved GP2_WCLK_SRC[1:0] 15, 12 14-13 Reserved Audio group 2 word clock source selector. Reference: Section 4.7.20 on page 57. R/W R/W 0 10 GP2_CH4_SRC[1:0] 11-9 Audio group 2 channel 4 source selector. Reference: Section 4.7.19 on page 56. R/W 111b GP2_CH3_SRC[2:0] 8-6 Audio group 2 channel 3 source selector. Reference: Section 4.7.19 on page 56. R/W 110b GP2_CH2_SRC[2:0] 5-3 Audio group 2 channel 2 source selector. Reference: Section 4.7.19 on page 56. R/W 101b GP2_CH1_SRC[2:0] 2-0 Audio group 2 channel 1 source selector. Reference: Section 4.7.19 on page 56. R/W 100b 40117 - 1 November 2007 92 of 114 GS1582 Data Sheet Table 4-44: SD Audio Configuration and Status Registers (Continued) Address 40Bh Register Name EN_NOT_LOCKED Bit 15 Description Asserts AUDIO_INT when LOCKED is not asserted. Reference: Section 4.7.14 on page 50. R/W R/W Default 0 EN_NO_VIDEO 14 Asserts AUDIO_INT when the video format is unknown. Reference: Section 4.7.14 on page 50. R/W 0 EN_MUX_ERRB 13 Asserts AUDIO_INT when the MUX_ERRB flag is set. Reference: Section 4.7.14 on page 50. R/W 0 EN_MUX_ERRA 12 Asserts AUDIO_INT when the MUX_ERRA flag is set. Reference: Section 4.7.14 on page 50. R/W 0 EN_AES_ERRD 11 Asserts AUDIO_INT when the AES_ERRD flag is set. Reference: Section 4.7.14 on page 50. R/W 0 EN_AES_ERRC 10 Asserts AUDIO_INT when the AES_ERRC flag is set. Reference: Section 4.7.14 on page 50. R/W 0 EN_AES_ERRB 9 Asserts AUDIO_INT when the AES_ERRB flag is set. Reference: Section 4.7.14 on page 50. R/W 0 EN_AES_ERRA 8 Asserts AUDIO_INT when the AES_ERRA flag is set. Reference: Section 4.7.14 on page 50. R/W 0 EN_ACPG4_DET 7 Asserts AUDIO_INT when the ACPG4_DET flag is set. Reference: Section 4.7.14 on page 50. R/W 0 EN_ACPG3_DET 6 Asserts AUDIO_INT when the ACPG3_DET flag is set. Reference: Section 4.7.14 on page 50. R/W 0 EN_ACPG2_DET 5 Asserts AUDIO_INT when the ACPG2_DET flag is set. Reference: Section 4.7.14 on page 50. R/W 0 EN_ACPG1_DET 4 Asserts AUDIO_INT when the ACPG1_DET flag is set. Reference: Section 4.7.14 on page 50. R/W 0 EN_ADPG4_DET 3 Asserts AUDIO_INT when the ADPG4_DET flag is set. Reference: Section 4.7.14 on page 50. R/W 0 EN_ADPG3_DET 2 Asserts AUDIO_INT when the ADPG3_DET flag is set. Reference: Section 4.7.14 on page 50. R/W 0 EN_ADPG2_DET 1 Asserts AUDIO_INT when the ADPG2_DET flag is set. Reference: Section 4.7.14 on page 50. R/W 0 EN_ADPG1_DET 0 Asserts AUDIO_INT when the ADPG1_DET flag is set. Reference: Section 4.7.14 on page 50. R/W 0 40117 - 1 November 2007 93 of 114 GS1582 Data Sheet Table 4-44: SD Audio Configuration and Status Registers (Continued) Address 40Ch Register Name MUX_ERRB Bit 15 Description Set in Cascade mode when the incoming video contains packets with the same group number as Group 2. Reference: Section 4.7.3 on page 38. R/W R Default 0 MUX_ERRA 14 Set in Cascade mode when the incoming video contains packets with the same group number as Group 1. Reference: Section 4.7.3 on page 38. R 0 XPOINT_ERROR 13 Set when the crosspoint switch is configured to put the same audio channel in both Group 1 and Group 2. Reference: Section 4.7.19 on page 56. R 0 MUTE_ALL 12 Mutes all input audio channels. Reference: Section 4.7.23 on page 62. R/W 0 LSB_FIRSTD 11 Causes the fourth stereo pair serial input formats to use LSB first. Reference: Section 4.7.17 on page 52. R/W 0 LSB_FIRSTC 10 Causes the third stereo pair serial input formats to use LSB first. Reference: Section 4.7.17 on page 52. R/W 0 LSB_FIRSTB 9 Causes the second stereo pair serial input formats to use LSB first. Reference: Section 4.7.17 on page 52. R/W 0 LSB_FIRSTA 8 Causes the first stereo pair serial input formats to use LSB first. Reference: Section 4.7.17 on page 52. R/W 0 ACT8 7 Specifies embedding of audio group 2 channel 4. Reference: Section 4.7.12 on page 50. R/W 1 ACT7 6 Specifies embedding of audio group 2 channel 3. Reference: Section 4.7.12 on page 50. R/W 1 ACT6 5 Specifies embedding of audio group 2 channel 2. Reference: Section 4.7.12 on page 50. R/W 1 ACT5 4 Specifies embedding of audio group 2 channel 1. Reference: Section 4.7.12 on page 50. R/W 1 ACT4 3 Specifies embedding of audio group 1 channel 4. Reference: Section 4.7.12 on page 50. R/W 1 ACT3 2 Specifies embedding of audio group 1 channel 3. Reference: Section 4.7.12 on page 50. R/W 1 ACT2 1 Specifies embedding of audio group 1 channel 2. Reference: Section 4.7.12 on page 50. R/W 1 ACT1 0 Specifies embedding of audio group 1 channel 1. Reference: Section 4.7.12 on page 50. R/W 1 40Dh-41Fh Reserved 15-0 Reserved. W N/A 40117 - 1 November 2007 94 of 114 GS1582 Data Sheet Table 4-44: SD Audio Configuration and Status Registers (Continued) Address 420h-436h 420h Register Name Reserved ACSR[7:0] Bit 15-8 7-0 Description Reserved Audio status block byte 0. Reference: Section 4.7.18 on page 55. R/W W W Default N/A 85h 421h ACSR[15:8] 7-0 Audio status block byte 1. Reference: Section 4.7.18 on page 55. W 08h 422h ACSR[23:16] 7-0 Audio status block byte 2. Reference: Section 4.7.18 on page 55. W 2Ch 423h-436h ACSR[183:24] 7-0 Remaining audio status. Reference: Section 4.7.18 on page 55. W 0 440h Reserved DEL1A[7:0] 15-9 8-1 Reserved Audio group 1 delay data for channel 1. Reference: Section 4.7.9 on page 45. W W 0000000b 0 EBIT1A 0 Audio group 1 delay data valid flag for channel 1. Reference: Section 4.7.9 on page 45. W 0 441h Reserved DEL1A[16:8] 15-9 8-0 Reserved Audio group 1 delay data for channel 1. Reference: Section 4.7.9 on page 45. W W 0000000b 0 442h Reserved DEL1A[25:17] 15-9 8-0 Reserved Audio group 1 delay data for channel 1. Reference: Section 4.7.9 on page 45. W W 0000000b 0 443h Reserved DEL2A[7:0] 15-9 8-1 Reserved Audio group 1 delay data for channel 2. Reference: Section 4.7.9 on page 45. W W 0000000b 0 EBIT2A 0 Audio group 1 delay data valid flag for channel 2. Reference: Section 4.7.9 on page 45. W 0 444h Reserved DEL2A[16:8] 15-9 8-0 Reserved Audio group 1 delay data for channel 2. Reference: Section 4.7.9 on page 45. W W 0000000b 0 445h Reserved DEL2A[25:17] 15-9 8-0 Reserved Audio group 1 delay data for channel 2. Reference: Section 4.7.9 on page 45. W W 0000000b 0 446h Reserved DEL3A[7:0] 15-9 8-1 Reserved Audio group 1 delay data for channel 3. Reference: Section 4.7.9 on page 45. W W 0000000b 0 EBIT1A 0 Audio group 1 delay data valid flag for channel3. Reference: Section 4.7.9 on page 45. W 0 40117 - 1 November 2007 95 of 114 GS1582 Data Sheet Table 4-44: SD Audio Configuration and Status Registers (Continued) Address 447h Register Name Reserved DEL3A[16:8] Bit 15-9 8-0 Description Reserved Audio group 1 delay data for channel 3. Reference: Section 4.7.9 on page 45. R/W W W Default 0000000b 0 448h Reserved DEL3A[25:17] 15-9 8-0 Reserved Audio group 1 delay data for channel 3. Reference: Section 4.7.9 on page 45. W W 0000000b 0 449h Reserved DEL4A[7:0] 15-9 8-1 Reserved Audio group 1 delay data for channel 4. Reference: Section 4.7.9 on page 45. W W 0000000b 0 EBIT4A 0 Audio group 1 delay data valid flag for channel 4. Reference: Section 4.7.9 on page 45. W 0 44Ah Reserved DEL4A[16:8] 15-9 8-0 Reserved Audio group 1 delay data for channel 4. Reference: Section 4.7.9 on page 45. W W 0000000b 0 44Bh Reserved DEL4A[25:17] 15-9 8-0 Reserved Audio group 1 delay data for channel 4. Reference: Section 4.7.9 on page 45. W W 0000000b 0 450h Reserved DEL1B[7:0] 15-9 8-1 Reserved Audio group 2 delay data for channel 1. Reference: Section 4.7.9 on page 45. W W 0000000b 0 EBIT1B 0 Audio group 2 delay data valid flag for channel 1. Reference: Section 4.7.9 on page 45. W 0 451h Reserved DEL1B[16:8] 15-9 8-0 Reserved Audio group 2 delay data for channel 1. Reference: Section 4.7.9 on page 45. W W 0000000b 0 452h Reserved DEL1B[25:17] 15-9 8-0 Reserved Audio group 2 delay data for channel 1. Reference: Section 4.7.9 on page 45. W W 0000000b 0 453h Reserved DEL2B[7:0] 15-9 8-1 Reserved Audio group 2 delay data for channel 2. Reference: Section 4.7.9 on page 45. W W 0000000b 0 EBIT2B 0 Audio group 2 delay data valid flag for channel 2. Reference: Section 4.7.9 on page 45. W 0 454h Reserved DEL2B[16:8] 15-9 8-0 Reserved Audio group 2 delay data for channel 2. Reference: Section 4.7.9 on page 45. W W 0000000b 0 40117 - 1 November 2007 96 of 114 GS1582 Data Sheet Table 4-44: SD Audio Configuration and Status Registers (Continued) Address 455h Register Name Reserved DEL2B[25:17] Bit 15-9 8-0 Description Reserved Audio group 2 delay data for channel 2. Reference: Section 4.7.9 on page 45. R/W W W Default 0000000b 0 456h Reserved DEL3B[7:0] 15-9 8-1 Reserved Audio group 2 delay data for channel 3. Reference: Section 4.7.9 on page 45. W W 0000000b 0 EBIT1B 0 Audio group 2 delay data valid flag for channel3. Reference: Section 4.7.9 on page 45. W 0 457h Reserved DEL3B[16:8] 15-9 8-0 Reserved Audio group 2 delay data for channel 3. Reference: Section 4.7.9 on page 45. W W 0000000b 0 458h Reserved DEL3B[25:17] 15-9 8-0 Reserved Audio group 2 delay data for channel 3. Reference: Section 4.7.9 on page 45. W W 0000000b 0 459h Reserved DEL4B[7:0] 15-9 8-1 Reserved Audio group 2 delay data for channel 4. Reference: Section 4.7.9 on page 45. W W 0000000b 0 EBIT4B 0 Audio group 2 delay data valid flag for channel 4. Reference: Section 4.7.9 on page 45. W 0 45Ah Reserved DEL4B[16:8] 15-9 8-0 Reserved Audio group 2 delay data for channel 4. Reference: Section 4.7.9 on page 45. W W 0000000b 0 45Bh Reserved DEL4B[25:17] 15-9 8-0 Reserved Audio group 2 delay data for channel 4. Reference: Section 4.7.9 on page 45. W W 0000000b 0 40117 - 1 November 2007 97 of 114 GS1582 Data Sheet 4.13.3.3 HD Audio Registers Table 4-45: HD Audio Configuration and Status Registers Address 800h Register Name CTR_AGR Bit 15 Description Selects replacement of audio control packets. 0: Do not replace audio control packets. 1: Replace all audio control packets. Reference: Section 4.7.11 on page 48. R/W R/W Default 0 AGR 14 Selects Audio Group Replacement operating mode. Reference: Section 4.7.11 on page 48. R/W 0 ONE_AGR 13 Specifies the replacement of just the group 1 audio. 0: Do not replace only Group 1. 1: Replace only Group 1. Reference: Section 4.7.11 on page 48. R/W 0 CTRB_ON 12 Specifies the embedding of group B audio control packets. Reference: Section 4.7.9 on page 45. R/W 1 ASXB 11 Group 2 asynchronous mode. Reference: Section 4.7.9 on page 45. R/W 0 AFNB_AUTO 10 Group 2 audio frame number generation. Reference: Section 4.7.9 on page 45. R/W 1 CTRA_ON 9 Specifies the embedding of group 1 audio control packets. Reference: Section 4.7.9 on page 45. R/W 1 ASXA 8 Group 1 asynchronous mode. Reference: Section 4.7.9 on page 45. R/W 0 AFNA_AUTO 7 Enables group 1 audio frame number generation. Reference: Section 4.7.9 on page 45. R/W 1 AFN_OFS[2:0] 6-4 Offset to add to generated Audio Frame Number. Must be in the range of 0 to 4. The resulting audio frame number will wrap around so as to always be in the 1-5 range. Reference: Section 4.7.16 on page 51. R/W 000b IDB[1:0] 3-2 Specifies the group 2 audio to embed. NOTE: Should IDA and IDB be set to the same value, they automatically revert to their default values. Reference: Section 4.7.10 on page 47. R/W 01b (normal mode) 11b (cascade mode) IDA[1:0] 1-0 Specifies the group 1 audio to embed. NOTE: Should IDA and IDB be set to the same value, they automatically revert to their default values. Reference: Section 4.7.10 on page 47. R/W 00b (normal mode) 10b (cascade mode) 801h Reserved 15-0 Reserved. W N/A 98 of 114 40117 - 1 November 2007 GS1582 Data Sheet Table 4-45: HD Audio Configuration and Status Registers Address 802h Register Name Reserved AES_ERRD Bit 15 14 Description Reserved Stereo Pair D audio input parity error when using AES format. Automatically cleared when read. Reference: Section 4.7.17.1 on page 53. R/W R R Default 0 0 AES_ERRC 13 Stereo Pair C audio input parity error when using AES format. Automatically cleared when read. Reference: Section 4.7.17.1 on page 53. R 0 AES_ERRB 12 Stereo Pair B audio input parity error when using AES format. Automatically cleared when read. Reference: Section 4.7.17.1 on page 53. R 0 AES_ERRA 11 Stereo Pair A audio input parity error when using AES format. Automatically cleared when read. Reference: Section 4.7.17.1 on page 53. R 0 ACPG4_DET 10 Set while Group 4 audio control packets are detected. Reference: Section 4.7.2 on page 37. R 0 ACPG3_DET 9 Set while Group 3 audio control packets are detected. Reference: Section 4.7.2 on page 37. R 0 ACPG2_DET 8 Set while Group 2 audio control packets are detected. Reference: Section 4.7.2 on page 37. R 0 ACPG1_DET 7 Set while Group 1 audio control packets are detected. Reference: Section 4.7.2 on page 37. R 0 ADPG4_DET 6 Set while Group 4 audio data packets are detected. Reference: Section 4.7.2 on page 37. R 0 ADPG3_DET 5 Set while Group 3 audio data packets are detected. Reference: Section 4.7.2 on page 37. R 0 ADPG2_DET 4 Set while Group 2 audio data packets are detected. Reference: Section 4.7.2 on page 37. R 0 ADPG1_DET 3 Set while Group 1 audio data packets are detected. Reference: Section 4.7.2 on page 37. R 0 ACS_APPLY_WAITB 2 Set while the GS1582 is waiting for a status boundary in the Group B group before applying the ACSR[183:0] data to that group. Reference: Section 4.7.18 on page 55. R 0 ACS_APPLY / ACS_APPLY_WAITA 1 Set while the GS1582 is waiting for a status boundary in Group A before applying the ACSR[183:0] data. Reference: Section 4.7.18 on page 55. R/W 0 ACS_REGEN 0 Specifies that Audio Channel Status of all channels should be replaced with ACSR[183:0] field. 0: Do not replace Channel Status 1: Replace Channel Status of all channels Reference: Section 4.7.18 on page 55. R/W 0 40117 - 1 November 2007 99 of 114 GS1582 Data Sheet Table 4-45: HD Audio Configuration and Status Registers Address 803h Register Name Reserved EN_CASCADE Reserved Bit 15-10 9 8-0 15-0 15-14 Description Reserved. Cascade. Reserved. Reserved. Audio input format selector for Stereo Pair D channels 7 and 8. Reference: Section 4.7.17 on page 52. R/W R R/W R R R/W Default N/A N/A N/A 11b 804h-807h 808h Reserved AMD[1:0] AMC[1:0] 13-12 Audio input format selector for Stereo Pair C channels 5 and 6. Reference: Section 4.7.17 on page 52. R/W 11b AMB[1:0] 11-10 Audio input format selector for Stereo Pair B channels 3 and 4. Reference: Section 4.7.17 on page 52. R/W 11b AMA[1:0] 9-8 Audio input format selector for Stereo Pair A channels 1 and 2. Reference: Section 4.7.17 on page 52. R/W 11b MUTE8 7 Audio input channel 8 mute enable. Reference: Section 4.7.23 on page 62. R/W 0 MUTE7 6 Audio input channel 7 mute enable. Reference: Section 4.7.23 on page 62. R/W 0 MUTE6 5 Audio input channel 6 mute enable. Reference: Section 4.7.23 on page 62. R/W 0 MUTE5 4 Audio input channel 5 mute enable. Reference: Section 4.7.23 on page 62. R/W 0 MUTE4 3 Audio input channel 4 mute enable. Reference: Section 4.7.23 on page 62. R/W 0 MUTE3 2 Audio input channel 3 mute enable. Reference: Section 4.7.23 on page 62. R/W 0 MUTE2 1 Audio input channel 2 mute enable. Reference: Section 4.7.23 on page 62. R/W 0 MUTE1 0 Audio input channel 1 mute enable. Reference: Section 4.7.23 on page 62. R/W 0 40117 - 1 November 2007 100 of 114 GS1582 Data Sheet Table 4-45: HD Audio Configuration and Status Registers Address 809h Register Name Reserved GP1_WCLK_SRC[1:0] Bit 15, 12 14-13 Description Reserved Audio group 1 word clock source selector. Reference: Section 4.7.20 on page 57. R/W R/W R/W Default 0 0 GP1_CH4_SRC[2:0] 11-9 Audio group 1 channel 4 source selector. Reference: Section 4.7.19 on page 56. R/W 011b GP1_CH3_SRC[2:0] 8-6 Audio group 1 channel 3 source selector. Reference: Section 4.7.19 on page 56. R/W 010b GP1_CH2_SRC[2:0] 5-3 Audio group 1 channel 2 source selector. Reference: Section 4.7.19 on page 56. R/W 001b GP1_CH1_SRC[2:0] 2-0 Audio group 1 channel 1 source selector. Reference: Section 4.7.19 on page 56. R/W 000b 80Ah Reserved GP2_WCLK_SRC[1:0] 15, 12 14-13 Reserved Audio group 2 word clock source selector. Reference: Section 4.7.20 on page 57. R/W R/W 0 10 GP2_CH4_SRC[2:0] 11-9 Audio group 2 channel 4 source selector. Reference: Section 4.7.19 on page 56. R/W 111b GP2_CH3_SRC[2:0] 8-6 Audio group 2 channel 3 source selector. Reference: Section 4.7.19 on page 56. R/W 110b GP2_CH2_SRC[2:0] 5-3 Audio group 2 channel 2 source selector. Reference: Section 4.7.19 on page 56. R/W 101b GP2_CH1_SRC[2:0] 2-0 Audio group 2 channel 1 source selector. Reference: Section 4.7.19 on page 56. R/W 100b 40117 - 1 November 2007 101 of 114 GS1582 Data Sheet Table 4-45: HD Audio Configuration and Status Registers Address 80Bh Register Name EN_NOT_LOCKED Bit 15 Description Asserts AUDIO_INT when LOCKED is not asserted. Reference: Section 4.7.14 on page 50. R/W R/W Default 0 EN_NO_VIDEO 14 Asserts AUDIO_INT when the video format is unknown. Reference: Section 4.7.14 on page 50. R/W 0 EN_MUX_ERRB 13 Asserts AUDIO_INT when the MUX_ERRB flag is set. Reference: Section 4.7.14 on page 50. R/W 0 EN_MUX_ERRA 12 Asserts AUDIO_INT when the MUX_ERRA flag is set. Reference: Section 4.7.14 on page 50. R/W 0 EN_AES_ERRD 11 Asserts AUDIO_INT when the AES_ERRD flag is set. Reference: Section 4.7.14 on page 50. R/W 0 EN_AES_ERRC 10 Asserts AUDIO_INT when the AES_ERRC flag is set. Reference: Section 4.7.14 on page 50. R/W 0 EN_AES_ERRB 9 Asserts AUDIO_INT when the AES_ERRB flag is set. Reference: Section 4.7.14 on page 50. R/W 0 EN_AES_ERRA 8 Asserts AUDIO_INT when the AES_ERRA flag is set. Reference: Section 4.7.14 on page 50. R/W 0 EN_ACPG4_DET 7 Asserts AUDIO_INT when the ACPG4_DET flag is set. Reference: Section 4.7.14 on page 50. R/W 0 EN_ACPG3_DET 6 Asserts AUDIO_INT when the ACPG3_DET flag is set. Reference: Section 4.7.14 on page 50. R/W 0 EN_ACPG2_DET 5 Asserts AUDIO_INT when the ACPG2_DET flag is set. Reference: Section 4.7.14 on page 50. R/W 0 EN_ACPG1_DET 4 Asserts AUDIO_INT when the ACPG1_DET flag is set. Reference: Section 4.7.14 on page 50. R/W 0 EN_ADPG4_DET 3 Asserts AUDIO_INT when the ADPG4_DET flag is set. Reference: Section 4.7.14 on page 50. R/W 0 EN_ADPG3_DET 2 Asserts AUDIO_INT when the ADPG3_DET flag is set. Reference: Section 4.7.14 on page 50. R/W 0 EN_ADPG2_DET 1 Asserts AUDIO_INT when the ADPG2_DET flag is set. Reference: Section 4.7.14 on page 50. R/W 0 EN_ADPG1_DET 0 Asserts AUDIO_INT when the ADPG1_DET flag is set. Reference: Section 4.7.14 on page 50. R/W 0 40117 - 1 November 2007 102 of 114 GS1582 Data Sheet Table 4-45: HD Audio Configuration and Status Registers Address 80Ch Register Name MUX_ERRB Bit 15 Description Set in Cascade mode when the incoming video contains packets with the same group number as Group 2. Reference: Section 4.7.3 on page 38. R/W R Default 0 MUX_ERRA 14 Set in Cascade mode when the incoming video contains packets with the same group number as Group 1. Reference: Section 4.7.3 on page 38. R 0 XPOINT_ERROR 13 Set when the crosspoint switch is configured to put the same audio channel in both Group 1 and Group 2. Reference: Section 4.7.19 on page 56. R 0 MUTE_ALL 12 Mutes all input audio channels. Reference: Section 4.7.23 on page 62. R/W 0 LSB_FIRSTD 11 Causes the fourth stereo pair serial input formats to use LSB first. Reference: Section 4.7.17 on page 52. R/W 0 LSB_FIRSTC 10 Causes the third stereo pair serial input formats to use LSB first. Reference: Section 4.7.17 on page 52. R/W 0 LSB_FIRSTB 9 Causes the second stereo pair serial input formats to use LSB first. Reference: Section 4.7.17 on page 52. R/W 0 LSB_FIRSTA 8 Causes the first stereo pair serial input formats to use LSB first. Reference: Section 4.7.17 on page 52. R/W 0 ACT8 7 Specifies embedding of audio group 2 channel 4. Reference: Section 4.7.12 on page 50. R/W 1 ACT7 6 Specifies embedding of audio group 2 channel 3. Reference: Section 4.7.12 on page 50. R/W 1 ACT6 5 Specifies embedding of audio group 2 channel 2. Reference: Section 4.7.12 on page 50. R/W 1 ACT5 4 Specifies embedding of audio group 2 channel 1. Reference: Section 4.7.12 on page 50. R/W 1 ACT4 3 Specifies embedding of audio group 1 channel 4. Reference: Section 4.7.12 on page 50. R/W 1 ACT3 2 Specifies embedding of audio group 1 channel 3. Reference: Section 4.7.12 on page 50. R/W 1 ACT2 1 Specifies embedding of audio group 1 channel 2. Reference: Section 4.7.12 on page 50. R/W 1 ACT1 0 Specifies embedding of audio group 1 channel 1. Reference: Section 4.7.12 on page 50. R/W 1 40117 - 1 November 2007 103 of 114 GS1582 Data Sheet Table 4-45: HD Audio Configuration and Status Registers Address 80Dh 820h-836h 820h Register Name Reserved Reserved ACSR[7:0] Bit 15-0 15-8 7-0 Description Reserved. Reserved. Audio status block byte 0. Reference: Section 4.7.18 on page 55. R/W W W W Default N/A N/A 85h 821h ACSR[15:8] 7-0 Audio status block byte 1. Reference: Section 4.7.18 on page 55. W 08h 822h ACSR[23:16] 7-0 Audio status block byte 2. Reference: Section 4.7.18 on page 55. W 2Ch 823h-836h ACSR[183:24] 7-0 Remaining audio status. Reference: Section 4.7.18 on page 55. W 0 840h Reserved DEL1_2A[7:0] 15-9 8-1 Reserved Audio group 1 delay data for channels 1 and 2. Reference: Section 4.7.9 on page 45. W W 0000000b 0 EBIT1_2A 0 Audio group 1 delay data valid flag for channels 1 and 2. Reference: Section 4.7.9 on page 45. W 0 841h Reserved DEL1_2A[16:8] 15-9 8-0 Reserved Audio group 1 delay data for channels 1 and 2. Reference: Section 4.7.9 on page 45. W W 0000000b 0 842h Reserved DEL1_2A[25:17] 15-9 8-0 Reserved Audio group 1 delay data for channels 1 and 2. Reference: Section 4.7.9 on page 45. W W 0000000b 0 843h Reserved DEL3_4A[7:0] 15-9 8-1 Reserved Audio group 1 delay data for channels 3 and 4. Reference: Section 4.7.9 on page 45. W W 0000000b 0 EBIT3_4A 0 Audio group 1 delay data valid flag for channels 3 and 4. Reference: Section 4.7.9 on page 45. W 0 844h Reserved DEL3_4A[16:8] 15-9 8-0 Reserved Audio group A delay data for channels 3 and 4. Reference: Section 4.7.9 on page 45. W W 0000000b 0 845h Reserved DEL3_4A[25:17] 15-9 8-0 Reserved Audio group 1 delay data for channels 3 and 4. Reference: Section 4.7.9 on page 45. W W 0000000b 0 40117 - 1 November 2007 104 of 114 GS1582 Data Sheet Table 4-45: HD Audio Configuration and Status Registers Address 846h Register Name Reserved DEL1_2B[7:0] Bit 15-9 8-1 Description Reserved Audio group 2 delay data for channels 1 and 2. Reference: Section 4.7.9 on page 45. R/W W W Default 0000000b 0 EBIT1_2B 0 Audio group 2 delay data valid flag for channels 1 and 2. Reference: Section 4.7.9 on page 45. W 0 847h Reserved DEL1_2B[16:8] 15-9 8-0 Reserved Audio group 2 delay data for channels 1 and 2. Reference: Section 4.7.9 on page 45. W W 0000000b 0 848h Reserved DEL1_2B[25:17] 15-9 8-0 Reserved Audio group 2 delay data for channels 1 and 2. Reference: Section 4.7.9 on page 45. W W 0000000b 0 849h Reserved DEL3_4B[7:0] 15-9 8-1 Reserved Audio group 2 delay data for channels 3 and 4. Reference: Section 4.7.9 on page 45. W W 0000000b 0 EBIT3_4B 0 Audio group 2 delay data valid flag for channels 3 and 4. Reference: Section 4.7.9 on page 45. W 0 84Ah Reserved DEL3_4B[16:8] 15-9 8-0 Reserved Audio group 2 delay data for channels 3 and 4. Reference: Section 4.7.9 on page 45. W W 0000000b 0 84Bh Reserved DEL3_4B[25:17] 15-9 8-0 Reserved Audio group 2 delay data for channels 3 and 4. Reference: Section 4.7.9 on page 45. W W 0000000b 0 4.14 JTAG Test Operation When the JTAG/HOST input pin of the GS1582 is set HIGH, the host interface port will be configured for JTAG test operation. In this mode, pins J9, J10, K9, and K10 become TDO, TCK, TMS, and TDI. In addition, the RESET_TRST pin will operate as the test reset pin. Boundary scan testing using the JTAG interface will be enabled in this mode. There are two ways in which JTAG can be used on the GS1582: 1. As a stand-alone JTAG interface to be used at in-circuit ATE (Automatic Test Equipment) during PCB assembly; or 2. Under control of a host processor for applications such as system power on self tests. 40117 - 1 November 2007 105 of 114 GS1582 Data Sheet When the JTAG tests are applied by ATE, care must be taken to disable any other devices driving the digital I/O pins. If the tests are to be applied only at ATE, this can be accomplished with tri-state buffers used in conjunction with the JTAG/HOST input signal. This is shown in Figure 4-31. Application HOST GS1582 CS_TMS SCLK_TCK SDIN_TDI SDOUT_TDO JTAG_HOST In-circuit ATE probe Figure 4-31: In-Circuit JTAG Alternatively, if the test capabilities are to be used in the system, the host processor may still control the JTAG/HOST input signal, but some means for tri-stating the host must exist in order to use the interface at ATE. This is represented in Figure 4-32. Application HOST GS1582 CS_TMS SCLK_TCK SDIN_TDI SDOUT_TDO Tri-State In-circuit ATE probe JTAG_HOST Figure 4-32: System JTAG NOTE: Scan coverage is limited to digital pins only. There is no scan coverage for analog pins VCO, SDO/SDO, RSET, LF, and CP_RES. NOTE: The SD/HD pin must be held LOW during scan and therefore has no scan coverage. Please contact your Gennum representative to obtain the BSDL model for the GS1582. 40117 - 1 November 2007 106 of 114 GS1582 Data Sheet 4.15 Device Reset In order to initialize all internal operating conditions to their default states, hold the RESET_TRST signal LOW for a minimum of treset = 10ms after all power supplies are stable. There are no requirements for power supply sequencing. When held in reset, all device outputs will be driven to a high-impedance state. Nominal Level 95% of Nominal Level Supply Voltage treset RESET_TRST Reset treset Reset Figure 4-33: Reset Pulse 40117 - 1 November 2007 107 of 114 GS1582 Data Sheet 5. Application Reference Design 5.1 Typical Application Circuit (Part A) PLACE AS CLOSE AS POSSIBLE TO THE PINS OF THE GS1582. CONNECT DIRECTLY TO PINS OF GS1582. +3.3V 10n VCO_GND 1 +1.8V_A +3.3V_CD GO1555 0R VCO_VCC VCO_GND 1 4 2.5V INTERNAL ISOLATED POWER VCO_GND 5 6 VCO_VCC VCO_GND 7 GND CONTROL SIGNALS RESETn SMPTE_BY PASSn DVB_ASI RESET SMPTE_BY PASS DVB-ASI SD/HD JTAG/HOST BLANK IOPROC_EN/DIS 20bit/10bit SDO_EN/DIS DETECT_TRS STANDBY TIMING_SELECT VCTR GND VCC GND NC GND O/P 3 2 1 2 1u 0R 1u SD/HDn JTAG/HOSTn BLANKn IOPROC_EN/DISn 20bit/10bitn 8 10n 10n 10n 1 2 SDO_EN/DISn DETECT_TRS GND_A 33uF 3R3 GND_A +1.8V IO_VDD 10n VCO_GND G1 H10 A5 E1 K8 G10 A10 B10 2 STANDBY TIMING_SEL CORE_VDD CORE_VDD CORE_VDD CORE_VDD PD_VDD PD_VDD CD_VDD IO_VDD IO_VDD C* 10KR VCO_GND VCO_GND A9 A8 B9 B8 B7 A7 DATA_IN19 DATA_IN18 DATA_IN17 DATA_IN16 DATA_IN15 DATA_IN14 DATA_IN13 DATA_IN12 DATA_IN11 DATA_IN10 DATA_IN9 DATA_IN8 DATA_IN7 DATA_IN6 DATA_IN5 DATA_IN4 DATA_IN3 DATA_IN2 DATA_IN1 DATA_IN0 PARALLEL DATA INPUT[19:0] PCLK INPUT (f rom GS4911B) PCLK_1582 B3 A2 A1 B2 B1 C2 C1 C3 D1 D2 F1 F2 H1 H2 J1 J2 K1 K2 J3 K3 B4 CP_VDD CP_GND *R & C: Refer to Section 4.11.2 for Loop Filter Component Values. VCO_GND A6 B6 E10 R* VCO VCO_VCC VCO_GND VCO_GND CP_RES LF DIN19 DIN18 DIN17 DIN16 DIN15 DIN14 DIN13 DIN12 DIN11 DIN10 DIN9 DIN8 DIN7 DIN6 DIN5 DIN4 DIN3 DIN2 DIN1 DIN0 PCLK F/DE V/VSY NC H/HSY NC AUDIO_INT GRP1_EN/DIS ACLK_1 WCLK_1 AIN_1/2 AIN_3/4 GRP2_EN/DIS ACLK_2 WCLK_2 AIN_5/6 AIN_7/8 RESET SMPTE_BY PASS SD/HD DVB_ASI JTAG/HOST BLANK IOPROC_EN/DIS 20BIT/10BIT SDO_EN/DIS DETECT_TRS STANDBY TIM_861 LOCKED G8 G6 E3 G5 H8 H3 G7 G4 D4 F3 D3 G3 H4 RESETn SMPTE_BY PASSn SD/HDn DVB_ASI JTAG/HOSTn ANC_BLANKn IOPROC_EN/DISn 20bit/10bitn SDO_EN/DISn DETECT_TRS STANDBY TIMING_SEL LOCKED GS1582 NC NC NC NC NC RSV NC D6 D7 D8 E4 E8 F4 F8 +3.3V_CD R and L form the Output Return Loss compensation Network. SUBJECT TO CHANGE 5n6 4u7 BNC F/DE_GS4911B A3 V/VSY NC_GS4911B C4 H/HSY NC_GS4911B A4 A_INT NP EN_GRP1 ACLK_1 WCLK_1 AIN1_2 AIN3_4 EN_GRP2 ACLK_2 WCLK_2 AIN5_6 AIN7_8 H7 H6 K7 J7 J6 K6 H5 K5 J5 J4 K4 750R +/- 1% RSET SDO SDO F10 C10 D10 +3.3V 22k K9 J10 K10 J9 CSn SCLK SDIN SDOUT 75R +3.3V_CD 75R GND_A BNC GND_A 10n FVH INPUT[2:0] (f rom GS4911B) 75R 75R 5n6 NP CS_TMS SCLK_TCK SDIN_TDI SDOUT_TDO CORE_GND CORE_GND CORE_GND CORE_GND CORE_GND CORE_GND CORE_GND CORE_GND CORE_GND CORE_GND CORE_GND CORE_GND 4u7 GND_A PD_GND PD_GND PD_GND CD_GND CD_GND CD_GND CD_GND IO_GND IO_GND GSPI[3:0] B5 C5 D5 E2 E5 E6 E7 F5 F6 F7 G9 J8 C6 C7 C8 C9 D9 E9 F9 GND_A AUDIO SIGNALS A_INT EN_GRP1 ACLK_1 WCLK_1 AIN1_2 AIN3_4 EN_GRP2 ACLK_2 WCLK_2 AIN5_6 AIN7_8 AUDIO INTERRUPT PRIMARY AUDIO GROUP ENABLE PRIMARY GROUP AUDIO CLOCK PRIMARY GROUP WORD CLOCK AUDIO CHANNELS 1 & 2 AUDIO CHANNELS 3 & 4 SECONDARY AUDIO GROUP ENABLE SECONDARY GROUP AUDIO CLOCK SECONDARY GROUP WORD CLOCK AUDIO CHANNELS 5 & 6 AUDIO CHANNELS 7 & 8 ANALOG POWER FILTERING +3.3V 0R +3.3V_CD G2 H9 10n 1u 1u 10n GND_A +1.8V 0R +1.8V_A 10n 1u 1u 10n (ACLK and WCLK may be supplied by GS4911B audio clock outputs.) 0R GND_A 40117 - 1 November 2007 108 of 114 GS1582 Data Sheet 5.2 Typical Application Circuit (Part B) GSPI_GS4911B[3:0] SCLK_GS4911B SDIN_GS4911B SDOUT_GS4911B CSn_GS4911B (NP) (NP) PCLK OUTPUT (To GS1582) JTAG/HOSTn GND_Bridge/PhS_A 1V8_Bridge/PhS_A 1V8_Bridge/PhS_A GND_Bridge/PhS_A GENLOCKn VDD_IO_A RESETn VDD_IO_A CONTROL SIGNALS GENLOCKn RESETn GENLOCK CONTROL RESET JTAG/HOST 38pF 0R LOCK_LOST_A REF_LOST_A 1V8_PCLK_A GND_VPLL/APLL_A VDD_XTAL_A GENLOCK NC IO_VDD RESET CS_TMS SDOUT_TDO SDIN_TDI SCLK_TCLK JTAG/HOST PHS_GND PHS_VDD PCLK1&2_VDD PCLK1&2_GND PCLK1 IO_VDD PCLK2 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 JTAG/HOSTn 27.000MHZ 1M 0R 24pF 1 2 3 4 5 6 7 GND_XTAL_A 8 9 1V8_PCLK_A 10 11 GND_VPLL/APLL_A 12 GND_VPLL/APLL_A 13 1V8_PCLK_A 14 15 16 LOCK_LOST REF_LOST VID_PLL_VDD VID_PLL_GND XTAL_VDD X1 X2 XTAL_GND CORE_GND ANALOG_VDD NC ANALOG_GND AUD_PLL_GND AUD_PLL_VDD 10FID HSY NC GS4911B LVDS/PCLK3_GND PCLK3 PCLK3 LVDS/PCLK3_VDD CORE_VDD TIMING_OUT8 TIMING_OUT7 TIMING_OUT6 TIMING_OUT5 TIMING_OUT4 IO_VDD TIMING_OUT3 TIMING_OUT2 TIMING_OUT1 ASR_SEL0 ASR_SEL1 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 GND_Bridge/PhS_A 1V8_Bridge/PhS_A VDD_Core_A FVH OUTPUT[2:0] (To GS1582) 22R VDD_IO_A 22R 22R F/DE_GS4911B V/VSY NC_GS4911B H/HSY NC_GS4911B +3.3V 10k 65 GND_PAD FVH TIMING INPUT[2:0] H_IN V_IN F_IN 17 VDD_IO_A 18 19 20 VID_STD0 21 VID_STD1 22 VID_STD2 23 VID_STD3 24 VID_STD4 25 VDD_Core_A 26 VID_STD5 27 28 29 30 VDD_IO_A 31 32 VSYNC IO_VDD FSYNC NC VID_STD0 VID_STD1 VID_STD2 VID_STD3 VID_STD4 CORE_VDD VID_STD5 ACLK1 ACLK2 ACLK3 IO_VDD ASR_SEL2 GS4911B AUDIO CLOCKS[2:0] 22R WCLK_GS4911B ACLK_GS4911B MCLK_GS4911B 22R (To GS1582 and audio sy nchronization dev ices.) 22R VIDEO STANDARD SELECT[5:0] ANALOG POWER FILTERING VDD_IO_A VDD_IO_A IO_VDD 0R 100nF 10uF 10uF 100nF DECOUPLING @ PINS 18,31,38,50,62 10nF 10nF 10nF 10nF 10nF +3.3V 0R 100nF 10uF 0R VDD_XTAL_A VDD_XTAL_A DECOUPLING @ PIN 5 10nF VDD_XTAL_A GND_XTAL_A 10uF 100nF GND_XTAL_A +1.8V 0R 100nF 10uF 0R 10uF 100nF 1V8_PCLK_A DECOUPLING @ PIN 45 10nF GND_XTAL_A 1V8_PCLK_A 1V8_PCLK_A GND_VPLL/APLL_A GND_VPLL/ALL_A +1.8V 0R 100nF 10uF 0R 10uF 100nF 1V8_Bridge/PhS_A DECOUPLING @ PIN 54 10nF GND_VPLL/ALL_A 1V8_Bridge/PhS_A 1V8_Bridge/PhS_A GND_Bridge/PhS_A GND_Bridge/PhS_A +1.8V 0R 100nF 10uF 10uF 100nF VDD_Core_A DECOUPLING @ PINS 26,44 10nF 10nF GND_Bridge/PhS_A VDD_Core_A VDD_Core_A 40117 - 1 November 2007 109 of 114 GS1582 Data Sheet 6. References & Relevant Standards SMPTE 125M SMPTE 259M SMPTE 260M SMPTE 267M SMPTE 272M Component video signal 4:2:2 - bit parallel interface 10-bit 4:2:2 Component and 4fsc Composite Digital Signals - Serial Digital Interface 1125 / 60 high definition production system - digital representation and bit parallel interface Bit parallel digital interface - component video signal 4:2:2 16 x 9 aspect ratio Formatting AES/EBU Audio and Auxiliary Data into Digital Video Ancillary Space 1920 x 1080 scanning analog and parallel digital interfaces for multiple picture rates Ancillary Data Packet and Space Formatting Bit-Serial Digital Interface for High-Definition Television Systems 720 x 483 active line at 59.94 Hz progressive scan production - digital representation 1280 x 720 scanning, analog and digital representation and analog interface 24-Bit Digital Audio Format for HDTV Bit-Serial Interface Video Payload Identification for Digital Television Interfaces Error Detection Checkwords and Status Flags for Use in Bit-Serial Digital Interfaces for Television Definition of Vertical Interval Switching Point for Synchronous Video Switching SMPTE 274M SMPTE 291M SMPTE 292M SMPTE 293M SMPTE 296M SMPTE 299M SMPTE 352M SMPTE RP165 SMPTE RP168 40117 - 1 November 2007 110 of 114 GS1582 Data Sheet 7. Package & Ordering Information 7.1 Package Dimensions 40117 - 1 November 2007 111 of 114 GS1582 Data Sheet 7.2 Marking Diagram Pin 1 ID GS1582 XXXXE3 YYWW XXXX - Lot/Work Order ID YYWW - Date Code YY - 2-digit year WW - 2-digit week number 7.3 Packaging Data Parameter Package Type Package Drawing Reference Moisture Sensitivity Level Junction to Case Thermal Resistance, j-c Junction to Air Thermal Resistance, j-a (at zero airflow) Junction to Board Thermal Resistance, j-b Psi, Pb-free and RoHS Compliant Value 11mm x 11mm 100-ball LBGA JEDEC M0192 (with exceptions noted in Package Dimensions on page 111). 3 15.4C/W 37.1C/W 26.4C/W 0.4C/W Yes 7.4 Ordering Information Part Number GS1582-IBE3 Package 100-ball BGA Pb-free Yes Temperature Range -20C to 85C 40117 - 1 November 2007 112 of 114 GS1582 Data Sheet 8. Revision History Version A B ECR 141222 144894 PCN - - Date March 2007 April 2007 Changes and/or Modifications New Document. Changed pin F4 to RSV and added drive strength values for pin H4, H7, and J9 in Pin Assignment and Pin Descriptions. Modified input voltage range parameter in Absolute Maximum Ratings. Updated serial output intrinsic jitter value in AC Electrical Characteristics. Added digital input/output circuits in Section 3. Added note to Section 4.7.20 Audio Word Clock. Converted to Preliminary Data Sheet. Changes were made in the following areas; Table 1-1: Pin Descriptions, 2.1 Absolute Maximum Ratings, 2.2 Recommended Operating Conditions, 2.3 DC Electrical Characteristics, 2.4 AC Electrical Characteristics, 4.3 SMPTE Mode, 4.3.1 HVF Timing, 4.6 Standby Mode, 4.7.20 Audio Word Clock, 4.8 Ancillary Data Insertion, 4.8.3 VANC Insertion, 4.9.4.1 SMPTE 352M Payload Identifier Packet Insertion, 4.9.4.3 EDH Generation and Insertion, 4.11.2 Loop Filter, 4.11.3 Lock Detect Output, 4.13.1 Command Word Description, Table 4-44: SD Audio Configuration and Status Registers, Table 4-45: HD Audio Configuration and Status Registers, 4.15 Device Reset, 5.1 Typical Application Circuit (Part A), 7.1 Package Dimensions, 7.2 Marking Diagram, 7.3 Packaging Data, 7.4 Ordering Information, Converted to a Data Sheet. Updates to: Note 4 in Table 2-2 on page 18, Audio Modes of Operation on page 38, Arbitrary, SMPTE 352M & EDH Packet Detect on page 40, Table 4-3 on page 39, Ancillary Data Insertion, Separate Line Mode on page 63, Concatenated Mode on page 64, Command Word Description on page 78, GSPI Host Interface, Table 4-33, Video Standard Indication, 2.3 DC Electrical Characteristics, Ancillary Data Checksum Generation and Insertion, Table 2-3: AC Electrical Characteristics, Interrupt Control,SMPTE 352M Payload Identifier Packet Insertion, SD Formats and HD Formats. 0 145472 - June 2007 1 146167 - November 2007 40117 - 1 November 2007 113 of 114 GS1582 Data Sheet CAUTION ELECTROSTATIC SENSITIVE DEVICES DO NOT OPEN PACKAGES OR HANDLE EXCEPT AT A STATIC-FREE WORKSTATION DOCUMENT IDENTIFICATION DATA SHEET The product is in production. Gennum reserves the right to make changes to the product at any time without notice to improve reliability, function or design, in order to provide the best product possible. GENNUM CORPORATION Mailing Address: P.O. Box 489, Stn. A, Burlington, Ontario, Canada L7R 3Y3 Shipping Address: 970 Fraser Drive, Burlington, Ontario, Canada L7L 5P5 Tel. +1 (905) 632-2996 Fax. +1 (905) 632-5946 GENNUM JAPAN CORPORATION Shinjuku Green Tower Building 27F, 6-14-1, Nishi Shinjuku, Shinjuku-ku, Tokyo, 160-0023 Japan Tel. +81 (03) 3349-5501, Fax. +81 (03) 3349-5505 GENNUM UK LIMITED 25 Long Garden Walk, Farnham, Surrey, England GU9 7HX Tel. +44 (0)1252 747 000 Fax +44 (0)1252 726 523 Gennum Corporation assumes no liability for any errors or omissions in this document, or for the use of the circuits or devices described herein. The sale of the circuit or device described herein does not imply any patent license, and Gennum makes no representation that the circuit or device is free from patent infringement. GENNUM and the G logo are registered trademarks of Gennum Corporation. (c) Copyright 2006 Gennum Corporation. All rights reserved. Printed in Canada. www.gennum.com 40117 - 1 November 2007 114 of 114 |
Price & Availability of GS1582-IBE3
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |